9116018911 Kenmore Range - Instructions

1. Turned off electrical breaker for range.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of the insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.

Pulled out bottom drawer and showed my 13 yr
old boy that the spring needed to go back in same hole, then he did the rest. It was so easy, even a 13 yr old can do it.

first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.

The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!

Cut Wires to old terminal block and wired in new Terminal Block

First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the oven, replaced the screws...good to go!

Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!

took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..

Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.

The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.

Removed the door. Unscrewed the hinge from front of oven. Took broiler drawer out. Unhooked the spring. Removed hinge. Screwed new hinge in. Rehooked the spring. Slid oven door back on hinges. Mission accomplished. Oven door works like a champ. Wife happy.

i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!

Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.

1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven