91146566892 Kenmore Range - Instructions

Removed the two screws, pulled out old element, installed new element, and reinstalled screws.

.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!

The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!

All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy

Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

Placed burners through opening in drip bowls and easily placed them on my stovetop

Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power

I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorced mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL

Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.

First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..

i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!

Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.

1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven