79095923300 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kelly from Marietta, GA
- Parts Used:
- 316135401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Largest burner was not operational
After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Mt. Vernon, AL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rusty worn out oven racks
Removed the old oven racks and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Basking Ridge, NJ
- Parts Used:
- 316135401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out in 15 months
Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kellyjean from Springfield, MA
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broiler element burned out.
Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hemet, CA
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
really bad ugly streaks inside of glass
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Krista from Newtown, CT
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
inner glass uncleanable
Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from Daleville, AL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat from bottom or top element,k stove top and clock all worked fine.
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Newark, DE
- Parts Used:
- 316203301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element broken
Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Hiram, OH
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't work
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Columbia, SC
- Parts Used:
- 316555800
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner wouldn't heat up
I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Orange, TX
- Parts Used:
- 316135401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke element.
Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARGARET from MILFORD, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner would not heat up
simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hiawassee, GA
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
wrong temp when baking.
removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Cranberry township, PA
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken oven door glass
I followed directions for replacement of the glass from the web. Replacement was simple and easy.
Was this instruction helpful to you?
Thank you for voting!