9117398810 Kenmore Range - Instructions

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

Assumed this broken hinge was going to be an expensive service call. Decided to try and fix it myself. Ordered the part off partselect.com and got some repair tips off the website that made this a breeze. I am not handy at all but was able to complete the replacement in less than 30 minutes and spent only $30 on the part. Just needed to unscrew the old hinge and release the spring from under the stove (which I accessed by pulling out the drawer). It would have cost me over $100 to just get a service person to look at it.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...

I really do not have the time to do this right now, however, I feel that it is important to tell everyone that dealing with PartSelect allowed me to repair the stove and please my wife in the easiest way possible. I will use PartSelect forever....

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...And then I installed
ignitor tightening the two screws and connected the two ignitor wires with the provided wire-nuts.
Mike Polcho

I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!

Slid off the oven door and loosened the hinge assembly. Removed the storage drawer to unhook the spring and then took off the old hinge assembly.

Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.

We can now bake bread, pizza, etc. What a relief.

The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.

It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.

I frist remove the screws that hold the element in place disconnected two wires.That didn't take long.Call aronud my area for part.They wanted 90.00 plus taxs.Went on line to find it much cheaper came in the mail very fast and put it in my self.Very easy and saved money too.It took less then 3 mins to put in.If I could do it you can too.Thank You,Bearice & Robert Reynolds P.S works great and no yelling at each other.Easy

Removed grills, oven bottom, heat deflector, and the two igniter mounting screws. Pulled out igniter, removed two wire twist caps and old igniter. Cut off ragged ends of wires coming from the stove side and re-stripped the wire ends. Attached oven side wires to new igniter wires using new twist caps. Reassembled everything in reverse order. Tested oven operation to ensure that the gas ignited promptly. (It did).

Pulled out bottom drawer and showed my 13 yr
old boy that the spring needed to go back in same hole, then he did the rest. It was so easy, even a 13 yr old can do it.

well first off I repair commercial HVAC equipment for a major drug company so I think I've done it all.I thought it cant be much different than any burner assembly.I made it harder than it had to be,anyone can do this.I removed lots of unneccessary things.Let me help you only take out the drawer on bottom of stove.so I started on top and worked my way down.save time and open the stove to were the door stops then have faith and give a good yank.this will remove the door,dont be afraid it will go right back on those two hinges easy.now that this is out of the way remove the bottom plate that covers the burner assembly (2 screws)in back pull it out then you see the igniter.as I said before with drawer pulled out remove the 2 1/4"nuts screws holding it up then from bottom.Unplug this stove then remove the 2 places its plugged in to.after you remove this there are 2 screws that hold it into the igniter remove them .cut the wires with enough room to re use the plug ends.strip the wires and use the wire nuts that they provide then put back together with new wires on new igniter then.re attach.put everything back together in the reverse order you took them apart.plug in stove and see the igniter light up again and light stove.do not call repairman you can do this.save your money for you its bad enough you have to buy anything else.

I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.

Lifted door off the front of stove, real easy, but heavy, took out old hinge, and replaced with new hinge, I just looked where everything was before, I replaced with new, replaced door back on, and I was finished.