79091043400 Kenmore Range - Instructions

Removed the drawer, simply snapped the rear drawer glide in the punch-out by hand, replaced the drawer. Works well

Lift stove top cover up and support cover so it will not fall down unplug element put new one in close cover and turn burning on and watch the burner get red hot. simple job why call a repair man in. Vicki

The repair was as simple as reattaching the broken glider. No tools were needed.

I watched the repair tutorial and followed the instructions. The order went very well and the tutorial was spot-on. Nice.

The drawer dropped down and would not easily open or shut or fit up good when closed. A quick inspection showed that one of the rear drawer guides was broken. The parts were ordered on a weekend and they showed up on Tuesday. We already had the pots and pans out of the drawer. It took about 10 minutes to put in the new guides (I replaced the one not broken also), clean and lubricate the drawer slides. Good as new. The repair video, although not necessary for this repair, was excellent. Thanks a bunch!

simply unplug the old burner and plug the new one it. not many repairs this easy. the best part of the whole thing is that the part arrived the next day.

Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

Just plugged it in! The hardest part was finding the model number. It was inside the top of the stove,while cleaning, I found it-on the left hand side when you take out the burner pans. I searched this site, found the part and when it arrived I just plugged it in and it worked fine. I would say less than 5 minutes to fix this issue.

This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey

I removed the old drip bowls from the top of the stove and replaced them with the new ones. I am not a handy person but even I had no problem doing it as I regularly remove them anyway to put them in the dishwasher to clean them.

First I want to thank Part Select for having the video online or I would not have attempted the repair. Also I saved over $75 on the parts!!!!!! It would have cost me $105 for parts and $125 for service tech to replace the burned off terminal blocks with new ones. Parts cost me $35 with shippiing, I did the repair saving me $195 !!!!!!!!! I replaced the parts as describied in the video and all is well. By the way, I got the parts in less than 24hours after ordering, cheaper than driving 30 miles to pick up overpriced parts !!!!

My brother is a licensed electrician, so the job was relatively easy for him. The pieces of insulation were pre-cut to fit, so there was no trimming involved. He tilted the oven over on its back to replace the piece of insulation under the oven. Removed the metal panel between the storage drawer and oven bottom, removed the soiled insulation and wiped everything down with vinegar. Placed the new insulation and reinstalled the metal panel and drawer. Removed the oven/range top and again removed the soiled insulation, wiped everything down and installed the new insulation (this piece of insulation was the wrap around one that goes under the range top - across the top of the oven and down both sides). Replaced the oven top, then did the back panel - this one was the most time consuming, due to the need to disconnect some of the wiring and sensors, as well as having to loosen the panel where the control knobs are located in order to remove the inner panel to get to the insulation. The insulation was precut to fit around the oven light bulb, so just had to make sure we installed it right side up :). Have used the oven several times since and no more smell!!

removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John

Reviewed the online repair video a few times then got started. Although only two were bad, I replaced all four terminal blocks. I removed the range top instead of using the built in kick stands. this left me much more room to work and I was able to clean the top of the range really well before getting started. Wires for the back terminals where short and a little difficult to use after cutting off the old terminal blocks. The terminal block mounting option for my style range included with the repair kit would not allow me to utilize the screw for the third wire on the left rear burner. I used a drill to carefully widen the hole in the mount to make the original screw fit as there are no screws included with the kit. This added the extra time to complete the repair. Over all the repair was simple to complete but having to modify the terminal block mount was dissapointing considering the web site selected parts for my specific model number. Still a bargain compared to what a service call or new purchase costs. I will be reparing my ranges from now on.