9113042590 Kenmore Range - Instructions

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

I took the old igniter out and replaced it with a new one.

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)

Removed old igniter coil by removing 2 small hex head bolts and pulling the two wire plug connectors (be sure to unplug the range). Installed new coil and connected the wires with the ceramic wire nuts supplied with the new part.

Basically followed the instructions that others had posted. Removed the bad oven igniter by removing the two screws securing it to the burner. Attached the new ignitor and then spliced the new wires into the old wires with the ceramic nuts that came with new igniter.

Removed bottom tray of oven, removed ignighter, unplug two wires.

Took off the 2 bottom covers, saw the igniter did'nt glow, checked for voltage,yes.Ordered part. when had part,pulled out ignitor,respliced wires, and did in reverse order.

I went to the GE website, did the trouble shooting and read that 80% of the time the igniter was the problem. I read how others did the repair, ordered the part and followed their steps. My only problem was the two screws were at a tough angle to get to, if it wasn't for that it would've been 15 minutes

It was a few days before Thanksgiving and our oven went out. We had out of town guests coming for a week stay with us. I fortunately found the instruction manual and hopefully thought it was the igniter. I called Parts Select and unbelievably I received it the next day. I checked with the helpfull hints to installing it. It was easy and quick. The only problem I had was laying on the floor to long, I had trouble getting up. I'm 70 years old. Thank you Parts select for having the part and your incredible delivery.

Removed the bottom cover plate and the bottom storage drawer. Disconnected the burner and removed it. Replaced the old igniter with the new one. The new one required the wire connectors from the old one to be spliced onto it. Reattached the ignitor to the burner and reinstalled the burner. Tested the new ignitor before reinstalling the cover plate and storage drawer.

The repair did not go well for the oven igniter. After I unfastened the defective igniter from the mount I tried to gently pull the ceramic wire connectors through the opening in the back of the oven. I pulled too hard and the wire connectors became disconnected and only the wires from the ingiter came through the opening. Now the wiring is trapped on the other side of the oven wall and I can't pull the wire through the opening (the oven is a wall unit). The wiring is actually also threaded through a second wall at the back of the oven and the wiring is trapped behind the second wall. I would need a long skinny hook to try to pry the wire from behind the second wall. I may need to call a professional after all. Jiggling the wires a bit in addition to gentle pulling may have worked, I don't know.

I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut the cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.