91193311010 Kenmore Range - Instructions

Had to move the range out of its little cubby hole in the kitchen so that I could have access to the back of the range. This process probably took the longest. After that it was a piece of cake. Took about 15 minutes to complete the job. So easy, eve a caveman could do it.

Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.

First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.

I first ordered the wrong part and had to call customer service. They handled the return and ordered the new piece beautifully!! The installation was really simple. Once I took out two screws holding the top down, I removed three clips holding the burner on then switched out the electrical leads. Put everything back and it worked perfectly!!

To 80 year old (young) brothers worked together. One hooked the wires the other one plug it in. Very simple install.. Neither one knows anything about electricity. Thank you for your service.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

The part came without instructions. The video was very helpful. But the whole process took 3 hrs.

well first i came here thewn i called got my part the next day by the way paying only regular postage. it took me more time to pull the stove out and find the sockets then to actually put the element in.that took a whole 3 minutes. thanks partselect you guys are the best and i will be back.

I simply turned the power off and slide the stove forward to give myself room to get behind it and just unscrewed the cover behind the burner switchers and pulled the switch knob off then I removed the two small screws that hold the burner switch to the control panel and go to the back and pull the wires carefully and replace them on the new switch one by one and screw the new switch to the control panel and replace the back panel and done!

Replaced drip pans

I just follow Steve's Installation Vidio. My range works.
Thanks Steve

First I removed the two screws that held the element in place. I then took the plate off the back of the range disconnected the two wires from the element and removed the old element. I then inserted the new element into the oven screwed the nuts back on and hooked the wires on the new element from the back put the plate back up on the back and screwed the nuts back on. It took around 15 minutes to do it all and this was the first time that I have ever done this. It was so easy.

Unplugged Stove. Removed two screws. Unplugged two wires from heating element. Connected the two wires to new heating element. Replaced screws. That's all. 5 minute repair job.....(45 minutes to find right socket haha)

Ordered new heating element on Friday afternoon (3pm) and received part on Saturday at 1:00pm. Impressive! (standard shipping)

removed the two screws,then pulled element out and removed the wires,took out element that needed replacing, then connected new element . the repair job took no time at all. i was really impressed with how easy it was.

Replaced