79075232311 Kenmore Range - Instructions

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

We carefully pulled the old seal out of the door ( staples hold it in place).Then took the replacement and laid it around the door. Starting at one side we adjusted the seal and pushed the staples into place. Making sure we folded the ends, we used a spoon to push them into the slots.

moved the range out to access back
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved

I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.

Oven is working great now.

Our issues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.

If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.

Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.

Thanks

Went well, and working thank you ??

Unplugged oven range, removed oven door (makes the work much easier, you can find how on YouTube) removed two bottom panels. Removed warming drawer to gain access to wires. Traced wire from ignitor unplugged it. Unscrewed ignitor from bracket. Carefully screwed new ignitor onto bracket. Plugged it in. Plugged in oven range. Turned on oven to verify proper operation. Turned off oven once it lit for a few seconds then replaced warming drawer, bottom panels and oven door.

I followed the guidance of the YouTube video presented by Steve from your company. It was very easy and direct. The only issue I had was disconnecting the igniter clip, once I wa able to remove the old one, everything else was simple. I really appreciate this video because it saved me a ton of money for repair cost. I will use this process again even if it is my refrigerator because it is a Frigidaire also. Thanks to Steve who was very direct, on point, and patient with making this repair video. Kudos!

first the temperature sensor then the igniter. started to do the igniter by using common sense then I used YouTube which made it a lot faster.
the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Used instruction video & replaced part.

The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.

Removed old Oven Bake igniter, aligned it and installed the new Oven Bake Igniter.