79092629810 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kellyjean from Springfield, MA
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broiler element burned out.
Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Newark, DE
- Parts Used:
- 316203301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element broken
Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from BENTONVILLE, AR
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner would no turn off.
A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from wakefield, RI
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
aluminum foil melted on oven bottom
It cannot be cleaned as it welded itself to oven bottom. Two screws in back of oven bottom and it lifted right out. The new bottom says "do not use aluminum foil" Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from Severna Park, MD
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
damaged bottom pan
Removed 2 back screws, lifted pan from rear and pushed front slightly forward/into oven until front lip cleared. Installed new pan in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from Beaverton, OR
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Aluminum foil on bottem of oven melted and made a mess on new stove
Unscrewed the oven bottom plate and removed. Put new one in place and screwed it in place. Stove looks brand new again and am so happy with the results.The part we received was a perfect match and arrived in a few days!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jill from new boston, NH
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
put aluminum foil on bottom panel of oven to catch drips. Big mistake. adhered to oven in minutes.
Removed 2 screws at rear of bottom panel. Removed old panel, replaced with new and screwed back in.Piece of cake. Plus this company was great to order from. received part the same day. Very happy. Would order through this company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from LITCHFIELD, CT
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad burner switch
removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John M. from PLEASANT PRAIRIE, WI
- Parts Used:
- 316490000
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no heat
Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Madison, AL
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Hot Surface Light won't turn off.
Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Hillsboro, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch was Sparking
So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Warfordsburg, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
burner switch burned out
Unplugged the main cord to the socket in behind range. Took back panel off. Unscrewed switch from its position on face of range. Switch is not a look alike switch to original, so had to pay attention to the labeling on both switches as to their identity. Removed one line at a time from old switch and placed on new switch. Rechecked positions of the wires and made sure there was no binding of the wire positions when installed. Mounted switch to same position previous switch was removed. Reinstalled back panel, plugged in range and tested switch. Very easy repair as long as you can see the labeling on back of switches. I used a light having a strap that is positioned on my head for best lighting possible for one person repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Jordan, AR
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven not heating up properly
I removed back cover and replaced the probe. The troubleshooting info indicated this is the problem 99% of the time. Guess what, it did not help! Further checks indicate that broil element may be out. Am going to resistance check and order if that is the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Van, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burners on high all the time.
Replaced control units that were malfunctioning.
Was this instruction helpful to you?
Thank you for voting!