79075909993 Kenmore Range - Instructions

un-pluged stove,removed the one screw holding the broken igniter. disconected the one wire. installed new igniter and slipped on wire. The igniter came with a new bracket, the old one rusted away which is why the old igniter broke.

Pulled out the stove, removed the screws that held on the back panel, took out the 2 screws that held in the element and disconnected the wires and put the new one in. I put the screw back in and was finished!

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

The stove was older so the burner was hard to get out. The small screw heads broke off, so I had to carefully center punch and drill out the screw bodies. The igniter screw was also frozen in the pot metal burner. That screw requied drilling and tapping with the installation of a new 6-32 screw. Once the burner was refurbished, the igniter mounted easily. Afte attaching the gas line and igniter wire, the burner worked great.

no need to remover burner. Lift top up use a 1x4x5" to hold top up. Use short #2 screw driver remove screw and replace with new igniter

It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!

I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!

Removed screws. Unplugged temp sensor. Put screws back in. So easy a caveman could do it.

Burner set screws froze up, was able to break 2 of 3 free and broke 3rd off. Used new simular screws to re- thread and fasten burner back in place. Bit of work but everything working. Used oppertunity to clean and re-level while I was at it. Everything good to go.

I looked up the error code on line and found it was likely a faulty oven temp sensor. I was able to find the part and diagram at partselect.com and placed an order. The probe was in stock and arrived within a couple days. The repair took only about 20 minutes and works fine now. Thanks for your help partselect.com!
Jim

If you intend to replace the igniter electrode ( part no. PS436633), purchase a minimum of twelve (12) top burner mounting screws ( part no. PS437925).

I also recommend that you replace all the electrodes since you have gone to the lengths described below to replace one igniter electrode.

After time, the heads of the mounting screws become brittle and break off when attempting to remove them with a 3/16" socket or nut driver.

Be aware that even the new screws are not exactly 3/16 hex, nor do they truly accept a 4.5 mm, or 5 mm socket. The 5 mm has to much slop, and the 4.5 mm, and 3/16" do not fully seat over the head.

First unplug the stove, and turn off the gas.

To remove the broken screws, I had to use a hand grinder to grind the heads off (you could be as careful as possible, but you will still damage the porcelain finish of the range top.) Unfortunately every screw has to be removed to lift the range top up enough to gain access to the electrode(s).

Along with the broken screws being in the burner casting, to replace the electrode, you have to remove the burner to work on it. Remove the insulated wire from the electrode, and then the gas line to the burner.

I recommend inspection of the insulated wires to see if they may be grounding out to the stove body. With the top removed and the burners still in place, plug the range back in. Turn any knob on (all electrodes should spark at the burner accept the bad one(s)). Observe the wires to see if there is sparking to the stove body. If there is none, continue to replacement instructions. If a wire is sparking to the body, wrap the damaged wire with HEAT RESISTANT tape. Standard vinyl electrical tape won't withstand the heat.

To remove the burner from the gas line, use a 1/2" open end wrench (preferably a tubing nut wrench) to remove the gas line along with an adjustable wrench to hold the burner to prevent damaging the gas line.

If your lucky, the cross point (Phillips head) screw that secures the electrode will remove without stripping, but don't count on it. I had to grind those screw heads off as well.

I used a size no. 30 cobalt drill in my drill press to attempt to remove the broken off screws, but because of the screw/drill size, I could not keep the bit on the hardened screw center, it kept walking off center. I ground the screws flush to the burner surface, used a center point drill, a center punch, and a spring loaded set point punch, nothing worked to keep the bit from wandering off center and into the soft metal casting.

I had to drill new holes with the no. 30 drill bit just to the right (or left) of the existing holes. Keep the same orientation and mounting distance when drilling, either to the right or to the left.

The new burner mounting screws did not work for mounting the electrode to the burning, I used small no. 6 self tapping screws to mount the new electrodes to the burner casting (the washer head was to large).

Reconnect the gas line(s) to the burner(s). It will be necessary to carefully bend the gas lines so as to line the new holes up with the top when remounting the burner(s).

If I had it to do over again, I would just donate the range as is, while explaining the problem to the donation center. After my experience, I personally don't think it is worth the trouble of replacing the electrodes on a range this old.

Hope this helps.

Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

older range required no tools to repair, pulled old gasket out of notches at bottom of door, popped clips out of pre-drilled holes, folded new gasket ends {2 inches} and pushed into door, pushed clips into place.

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.