9116248410 Kenmore Range - Instructions

I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. I then secured the new unit to the oven wall with the two screws.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices!
Thank you,

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace of tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.

orderd a replacement part. recieved it two days later then that evening installed it. there was a video online to show how to replace it. very useful if your not a do it yourselfer.

First i turned off the main electricity for the oven. Then I removed the two screws with my socket wrench. Then i pulled the element out about 3 inches then disconnected the 2 wires that heated the element. I simply reversed the process to put in the new bake element and i was done.

Replaced drip pans that the apartment Superintendent had in place with the correct drip pans and now cooking is beautiful again! No more uneven cooking on the stove top.

Watched youtube....

This is how I did it--but I would strongly recommend you do step 4 first, and skip step 3! Remember, because 240V circuits have 2 "hot" wires, they may be "hot" (120V to ground) even when switched off!

1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.

Watched youtube. Easy and fast!

Using a wrench, removed old element and simply installed new one - took less than 10 minutes and the oven was working again! Best part was how quickly the item reached us - ordered it on a Wednesday afternoon and had it by Friday afternoon, with no expedited shipping - Great Service!

Uplugged the oven and undid the back contact cover, removed the nuts inside the oven and slid out the element. Pushed the new element into place and secured it. Attached the contacts and replaced the cover. Plugged it in and got cookin'.

Inspected bake element. Found void. Ordered new bake element from Parts Select. Price was very reasonable. Part came the next day. Stove was fixed in 5 minutes. Great place to get appliance parts. Saved over $100 if repairman was involved.