79072853300 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Garland Futrell from CHESAPEAKE, VA
- Parts Used:
- 5304503232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Broken ; oven door inner glass
Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from GAINESVILLE, GA
- Parts Used:
- 5304524341
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from STREATOR, IL
- Parts Used:
- 316237805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The wire for the electrode lighter broke off when I plied the top off to clean underneath (don’t take the top off unless you unbolt the burners first)
Turn off gas,unplug,unbolt the burners(you have to do this to keep from bending and or kinking over the gas lines.Luck kept me from bending the lines out of whack.)All I needed was the electrode but I couldn’t find it available separately.I had to buy the whole front burner.Anyway remove the clip from the new part slide the electrode out.Tilt the top of the range up take the clip off of the old electrode slide it out put the new one in install clip.Plug it in,rebolt all the burners in.Careful not to bend the gas lines.put the top down turn on the gas,plug it in and light.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from SULLIGENT, AL
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Never received parts from PartSelect!!!
It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!
I do not recommend ordering from PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Janesville, WI
- Parts Used:
- GRLP3
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
No problem, just needed to convert to LP gas.
After looking over the installation instructions I was confident that I could perform this on my own, However, changing the burner orifices was a bit tricky. Getting the original ones out worked well, they stayed in the nut driver when it was lifted. One of the new ones fell out when inserting it. Thankfully it fell all the way down and I could retrieve it. A small piece of tape was needed to keep it in the driver. The rest of the install went per instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Richmond, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Crack in inner door glass
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ozone Park, NY
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Change on e of the inside glass
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from ALLIANCE, OH
- Parts Used:
- 5304505695
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Top burners were not lighting without a match
Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from FORT DEFIANCE, AZ
- Parts Used:
- 316237805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
The igniter won't work
On the front left burner would not ignite, after the installation of the new one, same problem, new one didn't fix.. I guess it's something with the electric igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Palestine, IL
- Parts Used:
- 5304505695
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
burner ingnighter would not lite burner
Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from ELIDA, NM
- Parts Used:
- 316207520
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not light
Removed old control installed new part oven worked ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- elizabeth from fall river, MA
- Parts Used:
- 316237000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven door BROKEN GLASS
Remove two screws from bottom of inside oven door slide oven door up of hinges in side of door has 2 more screws when removing hold handle it does come off at very bottom of door remove all screws cover comes off remove new glass from package and place over brackets put oven door cover back on put screws back on slide back on bracket put last screws on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!