9114698895 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- shawn from port richey, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The element on our three year old stove stopped working...this was the bottom bake element.
It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.
To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple
To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Covington, LA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Old element burned in half
I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Fort Collins, CO
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The bake element was burnt out.
It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from FRESNO, CA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element broke
Fast shipping, Very easy to install I am a senior and had no problems works Great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CLAY, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
The phillament ends were pointed straight and the one I removed from the oven were bent in an angle .
Bent the tips so the phillament can fit inside the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karilyn from KEWADIN, MI
- Parts Used:
- WB32X106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip pan was ruined by renter
I ordered a new drip pan. Piece of cake. Stove looks new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecilia from Cranbury, NJ
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
hinge on oven door was broken, so oven wouldn't shut
Lifted door off the front of stove, real easy, but heavy, took out old hinge, and replaced with new hinge, I just looked where everything was before, I replaced with new, replaced door back on, and I was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from BROOKFIELD, CT
- Parts Used:
- WB32X106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip bowl, was very hard to find one that fit my stove
Installed easily, was most impressed with the speed of delivery and it was the perfect size!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from west sayville, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element broke
first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from Layton, UT
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
wheel cracked
Pulled out bottom drawer and showed my 13 yr
old boy that the spring needed to go back in same hole, then he did the rest. It was so easy, even a 13 yr old can do it.
old boy that the spring needed to go back in same hole, then he did the rest. It was so easy, even a 13 yr old can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from State College, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The bottom bake element was burned out.
1. Turned off electrical breaker for range.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of the insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of the insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Martin, TN
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bake Element went out..flamed out pretty big light show when it happened
The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bethlehem, NH
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bake element sparked due to damage
Shut of circuit breaker. Removed two screws with socket set . pulled element out about three inches, disconnected and held wires in place with clip type closepins. pressed connections onto new element , secured screws and presto... All too simple and in less then 15 minutes.
Reading previous reviews was quite helpful
Reading previous reviews was quite helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TESS from BOSWELL, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
element broke, oven wouldn't heat - still doesn't
first husband removed the bolts unplugged old element wires -plugged in new element wires and but in bolts - unfortunately the oven still doesn't work not sure if element is bad or wiring, need professional help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Dayton, NJ
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element was not working in an old (50+ years old)GE electric oven
Replacement of the heating element only takes a few minutes...First, turn off the breaker/fuse to the stove, then just remove two screws , pull out the two connected wires to expose the connections, hook them up, and replace the screws to the cover plate. The connection/cover plate can be hinged or not hinged. Make sure you order the correct one. We ordered the wrong one at first, but were assisted by the returns dept. and received the correct one in 2 days. Great customer service, thanks partsselect.com!!
Was this instruction helpful to you?
Thank you for voting!