79094153312 Kenmore Range - Instructions

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.

Tilted the surface unit and proped it up with the metal arm then I unpluged the old 8"-surface element and replaced it with the new 8"-surface element that I purchased from PartSelect.com. I then lowered the surface unit turned the burner knob on and everything worked fine. Thanks PartSelect.com.

Very easy to repair! I removed the old burner and slid the new burner element in its place. It was as simple as that! No tools required. My one and only complaint would be that the old burner was slightly larger (within 1 inch or so) than the new one so the new one sits slightly crooked on the stove top. But it works just fine. The item also shipped very quickly. Within a day or two. I am very satisfied with the transaction overall.

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Easy as 1-2-3

Ensured breaker was off. My range is hot wired. Removed all cables from old terminal block with nutdriver. Used phillips head screw driver to remove old terminal block from back of range. replaced old terminal block with new one. Re-attached accessory cables to small terminals first, then the main cables to the terminal block using where necessary long nose pliers. It is important to make note of which cables are attached to each terminal of the block, so make a sketch PRIOR to removal. Also be careful how the cables are attached to the block. You are using 10 gauge cable with thick insulation. It is important that when pushing the range back into position the cable does not put too much pressure on the block as it will break it. That's exactly what happened to this last one. It probably cracked under the strain of the pressure of the cable and finally current running through it weakened it to the point where it broke off from the block causing it to short and trip the breaker.

Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

removed six nutdriver screws and removed rear cover. the only problem i had was the new switch they sent was a little larger then the orig.had to figure out the wires. fit good and works perfect.

Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.

The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.

First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was able to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.

I am an electrician so I had no problem identifying wire and connecting them properly. However there were no instructions provided with the part and the configuration of the new switch was different than the the old one. I doubt if a DIY individual would have been capable of handling this task. Also there were no safety warning with respect to electrical repairs, which is a must today.