79092552810 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melinda from Three Rivers, MA
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Rusted leveling foot
I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHERYL from PERRYVILLE, AR
- Parts Used:
- 316239700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Gasket missing
I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from N MYRTLE BCH, SC
- Parts Used:
- A316222301, A316222201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
showing age
bought drip bowl from big box store and the 8 inch did not fit . yours fit perfect will use you for future diy jobs thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Andrews, SC
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
switch had a diffirent lug configuration
made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!
Was this instruction helpful to you?
Thank you for voting!
Burners getting too hot.
Watch video. This oven had the connecters that popped off and on which made this task easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from MADISON HTS, VA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
L.F. large burner element either on full hot or off. Would not cycle in and out with element control switch setting.
Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it started but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- leslie from Pickerington, OH
- Parts Used:
- 5304506004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The glass on the enter oven door was broken
It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine H. from SEAL BEACH, CA
- Parts Used:
- A316222301, A316222201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
crummy chrome drip pans were worn out. replaced wtih enamel ones.
I just pulled the old ones out of the sockets, cleaned underneath, and replaced with new ones. No-brainer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Elmira, NY
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing oven racks
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PAINESVILLE, OH
- Parts Used:
- 316067902
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old racks had melted plastic on them.
It was a replace racks not repair. No problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from SULLIGENT, AL
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Never received parts from PartSelect!!!
It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!
I do not recommend ordering from PartSelect!
Was this instruction helpful to you?
Thank you for voting!
my burners would just heat up solid red even when i had controls turned down to 2 or 3. i would have to turn controls off and back on, then they still would just go back to glowing red
This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and Mama is happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dante from SOUTHOLD, NY
- Parts Used:
- 316436000
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Right rear burner not working properly
After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as the video showed his switch matched each wire? My installation was sideways??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from PORTLAND, OR
- Parts Used:
- 316225001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bottom element burned up
I am 78 years old and I watched the how to video twice and then did it so if I can do it anyone can,oh and I am a woman
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!