7909082040A Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alvie from Pasco, WA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
replaced the infinite burner switch
I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from Miles City, MT
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Large burner switch made popping and buzzing noises.
The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.
Was this instruction helpful to you?
Thank you for voting!
No heat to large coil; erratic heat with clicking noise to small coil
I followed the Parts Select Video that showed replacing an identical switch. Mine were another brand & style with different color wires. I took a picture of 1 to keep track of the wiring and removed it. I saw that the terminals were marked P, H1, H2, L1, & L2 so I put the wire from the same terminal onto the Parts Select switches & they work just fine now. The parts I got from you are heavier and a much better quality than the original equipment. I would also like to say that I was amazed at how fast this order was shipped, and the washer pump was a piece of cake thanks to your video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Moorestown, NJ
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Right Rear burner stopped working
I read other experiences on line and determined that it was either the element of the control switch. So I decided to order the control. When deciding I had removed the upper back sheild and put it back on. Subsequently a couple of days later there were popping noises culminating in a flash and the stove went 'dark'. I figured that I had pinched a wire when I put the upper shield back on. I removed the shield and looked for black 'short' marks. None were visible. I went to the electric panel and tried to reset the 60 amp breaker. It wouldn't reset and momentarily the lights dimmed. Uh-oh! Went back to stove and opened area where the cord connects to the stove. Direct short- a lose terminal block bolt had welded itself to the chassis! I redid all connections and lined inside of stove back with duct tape- also redid the connections with bolts, nuts and lockwashers covered each with electrical tape. Now reconnecting electric I put the new switch in. Removed the knob from the front and started to transfer the wires from the back. This was a little confusing because the control I received looked different from the one in the stove. After some checking I looked closely at the terminals on each control and they had tiny number/letters on them like H1, Li, H2 etc. So I just transferred H1 0n one cntrol switch to H1 on the new switch- L1 to L1 and so on. Put it all back together, turned on power and everything is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valentina from Riverside, CA
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Three terminal blocks burned out (disintegrated) on electric stove
First I want to thank Part Select for having the video online or I would not have attempted the repair. Also I saved over $75 on the parts!!!!!! It would have cost me $105 for parts and $125 for service tech to replace the burned off terminal blocks with new ones. Parts cost me $35 with shippiing, I did the repair saving me $195 !!!!!!!!! I replaced the parts as describied in the video and all is well. By the way, I got the parts in less than 24hours after ordering, cheaper than driving 30 miles to pick up overpriced parts !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from Pensacola, FL
- Parts Used:
- 316436000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No current to the burner
Checked the burner and no power to heat the burner. removed the old switch and put on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Lithonia, GA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner stays on when switch is in the off position.
Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Kingsport, TN
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Large element would only heat on high.
The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Forestdale, MA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Large burner doesn't turn down or shut off.
Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE
Was this instruction helpful to you?
Thank you for voting!
Needed new drip bowls
The hardest part of the job was cleaning under the old rings. Cook top looks new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Greenville, TX
- Parts Used:
- 316239700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket In Door Replaced
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Athens, OH
- Parts Used:
- 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element burned out
simply unplug the old burner and plug the new one it. not many repairs this easy. the best part of the whole thing is that the part arrived the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Virginia Beach, VA
- Parts Used:
- 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old element worn out
Removed old element and plugged in the new. Very simple and easy. Shipping and delivery was amazingly fast!
Was this instruction helpful to you?
Thank you for voting!