91195409000 Kenmore Range - Instructions

In order to replace the bottom trim (and side trims if needed) it is necessary to separate the oven door front panel and its outer glass from the inside door panel. It is best to remove the entire oven door and lay it down on a table in order to do this. (Refer to owner's manual for instructions on removing the door from the oven, but it basically lifts out easily when is is in the broil-open position). Remove the front panel of the oven door by unscrewing the two machine screws (these may be torx head screws on your appliance) on the top inside corners of the door that hold the door handle. (screw spacers on the inside likely will fall out when you remove the machine screws - don't be alarmed) Then remove the three screws at the bottom of door trim. The front panel can then be lifted away from the back panel. This will allow access to the screws that hold the bottom trim to the side trim. Remove these and the bottom trim will slide off. Replace trim pieces and reassemble.

Replace control switch

I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.

It is first necessary to remove the door from the range according to the manufacturer's instructions. Once removed, lay it down on a flat, protected surface with the outside facing down. Remove the two upper phillips screws and the hex nuts on the bottom channel. Next, separate the inside panel from the outside panel. You will then see the remaining hex nuts that have to be removed in order to replace either the bottom trim channel or the side pieces.

Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.

Pulled unit away from wall with help of husband and followed instructions.

Never did a repair like that. Had to ask store clerk what you call that thing you take off bolts with. But repair went great. Very satisfied. Part arrived very quickly and saved our Christmas dinner. THANK YOU!

I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!

First I unplugged the range. Then I removed the hex head screws, disconnected the two flag connectors and removed the old element. Then I reversed the process with the new element. I plugged the range back in and set the control to broil. It works like a charm!

Ordered part which arrived in 4 days. Removed range door (simple), removed shelves. With a power nut driver, removed support brackets holding element from top of oven. Removed screws holding element and temp probe at the rear of oven. Removed 2 wire connectors attached to element. Removed damaged element. Attached the replacement element to the 2 wire connectors and fed cables and probe wires back into the cable opening at the rear of the oven. Attached the new element to the top of the range with the existing screws. Attached the rear of the element with the temp probe with screws at the rear of the oven. Replaced range door. Plugged in power and tested for 15 minutes. Job complete. Parts price, great! Service call saved, priceless!

Removed the old element and installed the new one.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

very easy, door comes off without any tools. youtube has instruction for that. seperate the innerdoor pannel to access the screws for the trim.6 screws holding the trim. the hardest part was cleaning the rust off.

Dear PARTSELECT

My experience with you was spectacular!!!!

The oven broiler burner went out on a Sunday afternoon while my wife was using it to cook for our family dinner. We ordered it that day and it was received, installed, and working on Tuesday afternoon...



How could it be any better?



Thanks



George Crady

This repair is really easy unless the trim piece has rusted so badly that it's attached itself to the front door glass. It took a long time and some WD-40 to pry the trim off w/o breaking the glass. REPAIR: Remove the door and lay it on a flat surface. Unscrew the 3 bottom screws w/ small pliers, then unscrew the top two inside door screws w/ a small metric allen wrench. Remove the door trim to get to the last four side trim screws. Once the old trim is out just clean up any residue/rust remaining on the glass, install the new trim and reverse the steps to put the door back together. If the old trim comes off easily it should only take @ 20-30 minutes.