91193551991 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from OAKLAND, MD
- Parts Used:
- WB23K5027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Surface burner switch malfunction allowing the burner to remain on high heat after turning to low heat.
I removed two small screws located on the underside of the control panel. I then rotated the bottom of the control panel up and dislodged the few connections at top back of control panel. The control panel became loose enough to lay forward exposing the inner control switches. The old problem switch wiring was removed one by one and placed in the same spot on the new switch. The old switch was then removed by pulling off the front control knob and then unscrewing two screws holding the old switch in place. Then the new switch was installed exactly as the old switch was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HOUSTON, TX
- Parts Used:
- WB17X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Terminal Block was arcing.
Cut Wires to old terminal block and wired in new Terminal Block
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from PALM COAST, FL
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shortage in wiring cause the housing to burn out
Replaced new light housing.
Thanks to you guys for the prompt response
Thanks to you guys for the prompt response
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CASPER, WY
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad sensor
By myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Aberdeen, NJ
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Hanging broiler
Quick and easy, thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from PITTSBURGH, PA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken plastic handle end caps
Step #1: Remove 2 screws at the inside top of the oven door that holds the inner/outer oven door together. Step #2: Remove the screws from the inner door that hold the plastic handle end caps to the door. Tip: Use a file to dress up the tips of the metal handle bar so that it fits easily into the new plastic handle end caps. Step #3: Install the first new plastic handle end cap. Step #4: Slide the metal handle bar into the plastic handle end cap that was just installed on the outer oven door. Step #5: Place the other plastic handle end cap on the metal handle bar. Step #6: Install the second plastic handle end cap on the outer oven door. Step #7: Reassemble the oven door by installing the screws that were removed in step #1.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David H. from Arkadelphia, AR
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Double Oven door handles were off because of broken end pieces
Unscrewed three screws from each oven door. Unbolted the end pieces and replaced with new ones. Reinstalled oven door screws. Nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from Tucson, AZ
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Just follow the enclosed instructions
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vince from Newnan, GA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken door handle ends.
Removed door from unit, removed two screws on the insideof the door and open door in two, (inside and outside), removed two screws from each door handle end, replaced with new ones and Bingo !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Douglasville, GA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven door handle broke
My son took care of removing the broken parts, opening the door and replacing the new handle ends and then finished! It was easy watching him do the work!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from solsberry, IN
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken end caps on oven door
Very easy fix. After removing the six screws that held the door together, it was a cinch to replace the end caps and put the door back together. Works just like new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodolfo from Waterford, MI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Handle bracket was broken
Unscrewed the broken door handle from the range with torqx bit, and replaced, hardest part was getting the plastic handle on the black pull bar. you may want to use a mallet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Roanoke, VA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
End cap broke to the oven door
I took the old cap off, and replaced it with the new one. I am glad I had the sense to buy this online, If I had gotten a repairman to fix this, it probably would have costs $100.00 instead of the $17.00 it cost me to fix it myself. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from parkland, FL
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Both Door Handle End Caps broke
It took longer to go and buy the star tool then the repair. If you have the tools close it is a ten minute repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Southlake, TX
- Parts Used:
- WB7X7183
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
End caps very difficult to get on the handle bar
This the second time in three years the end caps broke. The first time the replacement end caps slid right on but, this time it was an extreemly tight fit. I had to sprsy white greese on the handle bar and inside the end cap and, even then I thought the end caps would break it was so hard to get on.
Was this instruction helpful to you?
Thank you for voting!