79071422400 Kenmore Range - Instructions

The repair shop wanted 150 dollars to fix it. I ordered the glass and replaced it myself. It was really easy and all I need was a screwdriver. It took me about 30 minutes total.

First I took the door off. Then I removed about a dozen screws. Than my wife insisited on cleaning the other two windows! Since the inside window was broken ;a lot of grease had gotten on the other two windows.She said she would never have another chance. After that I put everything back together. It took about an hour all together.

First I removed the oven door screws, then I removed the outer handle and then there were 2 more sets of screws that actually held 2 panes of glass onto the door.

took screws on outer sides and then removed glass put in new glass replaced screws done

Very simple with instructions supplied, Removed two screws inside on back of door, then removed four more screws to get to inner glass,removed broken glass installed new glass, replaced all screws.Job completed. very good instructions,Thank You.

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

PartsSelect.com saved me lots of $$$$$. I have had appliance repairers come and view the stove and tell me I needed so much work. I paid them and the stove still wasn't fixed. I figured out the problem and found PartsSelect.com = savior!

Bought a electric range/oven with a broken glass in the door cheaply because the owner didn't think they could fix the glass. I watched the video on You Tube on how to handle the spring loaded hinges and followed the steps as presented. The toughest part of the job was cleaning all the crud on all of the glass due to the gap in the inner glass. I had to use a square drive and a phillips head screwdriver to disassemble and reassemble the door. It took less than 30 minutes to complete the job and most of that time was cleaning the glass.

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.

The Conversion Kit was throughall with extra fittings and good instructions. My problem was haveing to pay a lisence gas installer $65.00 an hour to do a safety & pressure test. Maybee future Conversion kits would include a cheap disposable pressure tester with hose, then it would be a complete done job by the owner.

removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John

Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.

We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT

changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range

The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, you can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.