3639378810 Kenmore Range - Instructions

Easiest repair I ever did. Killed the circuit breaker, then removed the oven door, loosened the 2 hex nuts with a nut driver, pulled the old element out a few inches, loosened the nuts holding the wire to the element. I then put the new element in place, connected the wires to the element, pushed it back in to the insulation, and then replaced the nuts on the cover piece. Put the circuit breaker back on, and done!

I have a 22 year old GE double oven with a range top that I can't live without. I do alot of cooking, baking, and my share of entertaining. To replace this oven I would have to sacrifice having 2 ovens...or remodel my kitchen and reposition their location. So when something goes wrong with this oven I cringe. It needs to keep ticking for another 10 years. A friend recommended PartSelect. looked on line and found the part resembling mine. I called just to confirm the part was correct, and found out it was not. I looked up the part number the said was correct but the shape was wrong. I order it anyhow and when it arrived it was what I needed. The picture on the website was inconsistant with the part number. So I'm really glad I called and spoke to a rep. The part arrived in 4 days and the next day I installed it, needing only one tool. Doing it myself saved me a few hundred dollars and my oven works great again. And their price was lower than a local parts dealer. I added PartSelect to my favorite list for future needs! Thanks!

The replacement was a digital clock instead of analog. The directions were a little confusing, but adequate for the change. We removed the old clock, and followed the dirctions for replacing it. We made three tries to get the wires correctly connected and on the third try, it worked fine. However, I had to return the three knobs since the digital had push buttons. It fits into the space perfectly and we are very happy with it.

scissors and opened bag. determined that all three knobs were identical. aligned slots on each knob with flanges on each shaft.
snapped each knob into place.
Did a happy dance of empowerment around the kitchen. ( knobs had been broken for at least 5 years).
used timer to avoid burning christmas cookies.
Have a Merry one!!!

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

First turned off the circuit breaker. The two screws holding the element in place were removed. Next the element was pulled out about 3 inches. Wires were disconnected. Old element was removed. Wires were then attached to the new replacement element. The element was then re-attached to back of oven, using the two screws. Circuit breaker turned to on. About 5 minutes. Took longer to change the flashlight batteries!

First I removed the two screws in the back. then I removed the two screws attached to the brace at the top. pulled the old element out. Removed the screws that attatced the wires to the element. Attached the wires to the new element. Pushed the wires back in. Pushed the element in and attached the screws. Reattached the support. Turned on the broiler. The element smoked for a few seconds before getting red hot. It is working fine.

Pull the stove out from the wall and unplug. Had to remove back of stove, the aluminum sheilding and the duct work to get at wires use nut driver. Then used nut driver to remove nuts from broiler unit inside stove. Take the front overn dover off first. The new part did not match up with the wires so I used a needle nose to spread the wire clips just a tad so they would fit over the tabs of the broiler unit. Do all of this behind the stove as you do not have eough wire to do this effectively from the oven side. After I had the tabs fitted to the broiler unit. I removed them and fed wires back through the stove. I then went back to the front of the stove and put the broiler back in and put support bar back in to ceiling of stove and the two nuts back on to affix broiler to back of oven. Put the aluminum baccking and duct work back onto the back of the stove and plugged it back in. Pretty easy job.

Moved stove from wall, unplug the stove from the wall outlet, remove the oven racks, unscrew the plate against the oven wall supporting the element with a small adjustable wrench, pull out the element slowly without tearing the insulation & stretching the two wires, unscrew with a phillips screwdriver each wire with care, as a precautionary measurement: do not make contact with the other wire and any other part of the stove, even though it was still unpluged. Install the new element in reverse procedure...turn on Bake Element on low temperature..when it glows when hot..ready to go.

Turned off power at panellboard. Disconnected mounting hardware from inside oven chamber. Pulled failed heating element with wires attached into the oven chamber. Disconnected wiring and reconnected them to the new heating element. Tightened screws while holding connectors with pliers. Applied electrical tape to connections. Pushed wires back into opening and secured heating element back into place. Restored power nad verifed proper operation. The other heater purchased will be used when the bake element finally fails,

(1) Turned off power source.
(2) Removed rust on screw heads before attempting to loosening them up.
(3) Pulled the element out to expose the connections.
(4) Disconnected with phillips screw driver, taped off wires to prevent mixed-up during re-installation.
(5) Re-installed new element using new screws provided.

First thing to do is to KILL THE POWER. The last thing you want is for two leads feeding power to a range coil burner "hot" when you are working on them. After power is off, I removed the coils and set them aside. The terminals had "fried" apparently from to much cooking with hot oils and having the "over splash" working its way down to where the coils plug into the terminals and over time the oil getting in the terminals causes shorting / frying of the leads / contacts.

Anyway, after removing the heat coils I removed the drip pans and cleaned up the area underneath before working on terminals. I like a clean area when I work. I then unscrewed the "brackets" that house the terminals with a Phillips screwdriver and pulled out the assembly.

To completely remove the assembly I cut with a straight razor the existing heat shrink around the wire nuts (These two had been replaced once before. On first go around, I just cut the terminal assembly off and stripped the wire to attach the new terminals). Then I removed the wire nuts and the old assembly. After that I trimmed the wire to the correct length on the new terminal assembly and checked that the wire from the stove was in good shape. Upon confirming I had a good lead, I connected the new terminal leads to the stove leads and put the heat shrink over the connections. I used a lighter to "shrink" the heat shrink to the new connection (not having a proper heat shrink gun, which most of us don't have, the lighter works well as long as you are careful and do not let the lighter heat up to much. Let the lighter cool (esp. if a plastic disposable type or it will melt and ruin the lighter or burn your fingers).

After that I cleaned the area where the terminal block bracket connects to the stove (it gets a bit gunked up over time) before screwing in the new bracket / assembly in place with my screwdriver.

I gave the drip pans a good cleaning, adjusted the new terminal brackets so they were even / centered, cleaned once more the area under the drip pan and replaced the drip pans. The types of pans I have are one piece with a hole for the heat coil leads to go through.

Before placing the coils back in the terminals I took a strip of medium grade, 220 grit, sand paper (you could use steal wool or small wire brush) and cleaned the terminal leads (the steal end that plugs into the terminal only, careful not to damage the burner). This was needed as the leads had accumulated some residue from the same dynamics that caused the burning / melting of the terminal leads and terminal block. Once the leads were clean I fitted them into the place in the new terminal blocks and drip pan grooves.

Finally I turned back on the breaker to the stove and cranked on the burners to test out the connection and that everything was working A-OK.

Job done:-)

I'm a pharmacist and no handyman but this was extremely simple. Don't let a burned out element lead to a $1,000 purchase of a new oven. I removed 2 screws in the plate using a nut driver inside the oven where bake element exits the oven (keep sheet metal screws). Removed duct work from rear of oven to expose insulation where wires are attached to element using standard screw driver. Cleaned inside of unkown chemicals spewed out during fire. Inserted new bake element, screwed wires onto element from back (2 hot wires go on one side since it's 220). I tried to use the screws that came with the element but they didn't work so I was able to use the old sheet metal screws to secure the element to the inside of the oven. Replaced duct work on back. Done.

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]