9119188710 Kenmore Range - Instructions

Turn off power at the circuit breaker before working on electric thing.

Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)

1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven

The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.

Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.

I followed the instructions of a PartSelect.com customer that was posted on the website. The instructions were great and the repair only took 15 mins. Before I found the PartSelect website I called the dealer who we bought the stove from and they wanted $ 250 for the repair. I went on the PartSelect Website and received the parts within 2 days.
Total cost $ 59.65 thru PartSelect. Thanks PartSelect--Great service and Great website

Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

Really easy.
1) Pulled up on oven door and removed it.
2) Removed lower drawer to access springs.
3) Pay attention to which hole the springs are attached under the oven.
4) Remove spring with Needle Nose Plier. If you remove by hand, the spring will likely cut your finger....like mine.
5) Unscrew 3 screws of old hinge assembly.
6) Reverse process when placing new assembly in place.

Followed the excellent removal and installation video by PartSelect. Also the diagram was excellent allowing me to purchase the correct hinge the first time. Fast shipping.

At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!

Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Easy

Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.