79093751103 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Kettlersville, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner burned out
unplugged old burner plugged new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Smtella from Wappapello, MO
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
My burner would stay on high regardless of where it was set.
We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kellyjean from Springfield, MA
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broiler element burned out.
Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Newark, DE
- Parts Used:
- 316203301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element broken
Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JILL from VIRDEN, IL
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Large Burner On Glass Top Quit Working
Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Hiram, OH
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't work
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from Daleville, AL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat from bottom or top element,k stove top and clock all worked fine.
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from NORTH PORT, FL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
no heat in oven
replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from cana, VA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the stove eye would go to high and stay
watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sharon from Summerton, SC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element not heating right
Took old one out and plugged the new one into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Williston, SC
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Control Rod On Switch Was Broken Off
I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Peoria, IL
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Infiniti switch needed to be changed.
Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.
Was this instruction helpful to you?
Thank you for voting!
burner switches had only two settings off and high
After making sure it was the switches themselves not the burners that were the problem, it was easy locating the exact parts I needed on PartSelect and the shipment arrived in a timely manner. I had to replace two out of four switches. Using a screwdriver, I detached the display pannel and removed the faulty switches. Then I disconnected the old wires and attached them to the new switches, one at a time. Closed everything up and the "new" range works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fanny from Alhambra, CA
- Parts Used:
- 316468601
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I had the top trim broken on the oven door.
Very simple repair. I received my part a few days after placing order; then installed it myself. Anyone can do this simple easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Williamsville, VT
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace terminal block and burner unit.
Very simply following the online video instructions.
Was this instruction helpful to you?
Thank you for voting!