91194490300 Kenmore Range - Instructions

Loosened screw on upper left on the inside of the door,this enabled me to see exactly where to place the glass front, then slid the glass behind the door handle, then inserted into the bottom slot, making sure that the glass was secure. Did all of this after applying the insulation pad. Door looked like new!!!

I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However, after the new sensor the oven will maintain a more even temperature for the cycle.

Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.

At best a temporary fix for a an appliance this old.

I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried the oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.

unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block

Removed old racks and replaced with new racks.

I first turned off power, then I removed the old top oven heating element, I connected the new element to power supply then placed the element back into holders.

0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!

That's it! It took about 20-30 minutes.

Took out the 2 screws,Pulled out the stove
Took the back off ,took the wires out of the little place where they fit in,Removed the old element.
Put the new one in Fitted the little thing which looked like a alumium flat piece back where we took the old one out.Put the back back on cut it on wheepe In business.Also the new element came here faster than I thought it would .I,m a 71 yearold grandmother.Pretty simple.

My stove would not heat. I could see that the bake element had a hole burned through it. Found this website. I was confused about what part I needed so I called the phone number and the girl was very good at locating exactly which element my stove needed after I gave her the stove make and model #. I ordered the part on Thursday afternoon. The part arrived on Saturday afternoon.

The hardest part of fixing it was finding the correct screw driver socket thingy (I'm not a technical person) to get the screws off with. Thankfully my neighbor had what I needed. I pulled my stove out from the wall (primarily because I needed to clean under there) and unplugged it. Unscrewed the screws, pulled the old element out until I could see the wire connections. I used clothes pins to hold the wires from going back into the stove once I unhooked them from the element (another tip I learned on this website) and simple slipped the wire connectors onto the new element, pushed it back into place, put the screws back on, plugged it in and TA DA... was baking a pizza in no time.

Very very VERY easy repair!!!

Simply pulled old gasket from door and pushed new gasket clips into existing holes and tucked in ends at bottom of door.

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

Performed repair using a video for reference.

Pulled the range out and unplugged it. Removed the back panel. Removed one wire at a time and plugging it in on the new switch. unscrewed the existing switch from the front panel (Two screws). Screwed the new one in, replaced the panel, plugged in the range and tested it. The new switch was a perfect OEM replacement and worked perfectly.

Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.

The repair was very easy and your video was extremely helpful. Especially regarding pulling the oven out and removing the back wiring cover to get to the spade terminals, rather than trying to do it all from inside the oven. Added bonus was that I got that pocket for the oven cleaned out like new! Eww! Pulling it out also gave me enough reach without having to remove the oven door (didn't realize you cold do that). Best part though was your mention that GE often DROPPED the zeros in their parts numbers. Couldn't locate the part on any website until yours noted this. so.. you got the sale. Went back to GE's website, located it and found your quality part was also less expensive! 11 minutes start to finish, quick shipping and works great! I'll be back! Thank you!