Models > 79060071791 > Instructions

79060071791 Kenmore Range - Instructions

Jump to:

All Instructions for the 79060071791
46 - 60 of 103
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dominick from Greensburg, PA
Parts Used:
5303051140
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Broiler element burned out
I removed the four screws holding the element in place and pulled the element out and disconnected the two wire. Installation was pretty much the reverse of the removal except, when I went to put the two screws holding the element to the top of the oven I discovered the holes were rusted out. I looked for inserts to put in the holes but every time I tried different inserts the holes got bigger. I finally realized the oven is just sheet metal so I moved the bracket about an inch drilled new holes and used self-tapping screws.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from UNION, OR
Parts Used:
5303935058
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
replaced terminal block for element
followed the video provided on line which was very helpful..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Georgiana O from E MONTPELIER, VT
Parts Used:
316442300, L304430992
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replacement
remove old, set in new
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from FREDERICKSBRG, VA
Parts Used:
316442300
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Burner would cutoff intermittently
Pulled out old burner/inserted new
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chuck from EVANSVILLE, IN
Parts Used:
5303935058
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from LANOKA HARBOR, NJ
Parts Used:
318372210
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shelley from CLYDE, TX
Parts Used:
L304430992, 316048413
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Old bowls were rusted beyond ability to clean
Put the new bowls under the stove top burners with disposable liners to protect them. They look very clean and shiny now!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from PRAIRIEVILLE, LA
Parts Used:
5303935058
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from MENASHA, WI
Parts Used:
5303935058
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 burner elements not heating
Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharon from TEMPLE, GA
Parts Used:
5303935058
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Heating coils stop heating
Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tony from Hartford, CT
Parts Used:
5304409888
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jackie from Charlotte, NC
Parts Used:
318372210
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Left rear burner had a damaged burner prong.
I just had to plug the new burner plate in the receptical
and it works again very well.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Josephine from Malden, MA
Parts Used:
316048413
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Pitted, Eroded Drip Pans
1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Abraham from Albion, NY
Parts Used:
L304430992, 316048413
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Corroded chrome drip bowls.
Merely removed the old drip trays and replaced them with the new ones I ordered.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
david a from whitingham, VT
Parts Used:
L304430992, 316048413
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replace drip pans
replaced drip pans due to rust
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 79060071791
46 - 60 of 103