9119342191 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from OAKLAND, MD
- Parts Used:
- WB23K5027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Surface burner switch malfunction allowing the burner to remain on high heat after turning to low heat.
I removed two small screws located on the underside of the control panel. I then rotated the bottom of the control panel up and dislodged the few connections at top back of control panel. The control panel became loose enough to lay forward exposing the inner control switches. The old problem switch wiring was removed one by one and placed in the same spot on the new switch. The old switch was then removed by pulling off the front control knob and then unscrewing two screws holding the old switch in place. Then the new switch was installed exactly as the old switch was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUISA from EDEN, NC
- Parts Used:
- WB30X354
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Replaced hinge mounted burner
Parts arrived bent and element had tape residue on it. After approximately 1 hr. I was able to clean, make parts straight and install it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Houston, TX
- Parts Used:
- WB30X354
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old surface burner burned out one of its two circuits.
I unscrewed the old burner from the stove, took off the three wire to the heating element marking down where each colored wire went, taped off the exposed wires, ordered the new burner, and waited for it to arrive. When it got here, I installed it, and believe it or not, the new burner works just fine!. End of exciting repair story.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Houston, TX
- Parts Used:
- WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner started sparking and burned right through the coil
Took the old part off and marked the wiring for easy replacing and looked all over town and no part to match, so I went to the Internet and put in 8" burner and luckily found your website. The part was perfect and saved me alot of time doing more research for the part. Thank you for the quick shipment and good correspondence.
I will definitely use you again for parts and tell my friends about your website too.
I will definitely use you again for parts and tell my friends about your website too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pierre from South Burlington, VT
- Parts Used:
- WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
burner element was blown
Remove the old element by removing one screw and inserted new element and replaced the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carl from orange, CT
- Parts Used:
- WB23K5027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
large burner would not reduce heat when turned down
unplug stove, unscrew two screws on front of rangetop holding element controlls pry off controll handle and unscrew element controll, swing top up and off hinge.one at a time with needle nose plyers pull off wires and connect on new element controll.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Beckley, WV
- Parts Used:
- WB30X354
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
one element suffered a small puncture where the heated element burned thru
The old burner was disconnected by unscrewing the wire connectors. The new burner was installed by reconnecting the same wire connectors although the white and red connectors had to be swapped to make the inner element go on when #2 or med switch is chosen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Watertown, WI
- Parts Used:
- WB23K5027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner shorted Out. replaced plug...didn't fix
2 screws located underneath of the control panel. Unplugged the stove first! Pulled the leads out of the old switch and plugged into the new switch making sure wires went to the same location. SIMPLE! It works as good as new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian L from Ephrata, PA
- Parts Used:
- WB23K5027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Large Burner temperature malfunction
Remove the knobs on control panel. Removed a few screws. Remove wire fasteners from old part. Re-installed new part, re-fastened wires, re-installed control panel & screws, re-installed knobs. Tested burner on low, medium & high settings to confirm heat adjustment. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from STREATOR, IL
- Parts Used:
- WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element was not heating
I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connecting the 3 wires, I reattached the element to the range.
Was this instruction helpful to you?
Thank you for voting!