91195191990 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glenn from Newnan, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Defective
Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from conover, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
element broke
shut power off to range, took 2 screws out, took 2 snap on clips off old element. put snap on clips on new element, put 2 screws back in, and turned breaker on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dumfries, VA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven bake element burned out (literally!)
Removed oven door & shelves. Removed the 2 mounting screws & compared parts to verify I ordered the right one, then plugged it right in! Managed to drop & lose one of the screws while re-installing them. Got a stainless sheet metal screw from the hardware store that fits, but will probably order an exact replacement because the size & thread are slightly different. All in all, other than losing the screw, it was a quick, easy task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from Roy, UT
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element was broken
Remove the oven racks, remove the two retaining screws, unplugged the wires. Install wires on new bake element, insert element into opening, install & tighten retaining screws, replace oven rack's & there you have it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Okeana, OH
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element set itself on fire and burned in half
First - really check that the part you order will fit. Our oven is 30 years old and the first part we ordered was not correct, but it came the very next day after we ordered it which is amazing. We were more careful about measuring for the second one and it came almost as quickly. It only took a few seconds to unscrew the old element and then reattach the wires to the new one and screw it back into the oven. Very simple. I highly recommend PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dane from Baton Rouge, LA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was burning food
Two screws hold the element to the oven wall. two wires attached to the back of the element. very simple removal and replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from MAHWAH, NJ
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
bake element burnt out
unscrewed it unhooked the wires and replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Murray from Franklin Square, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element burned out, lower unit
removed nuts from inside, removed rear panel, pulled old
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from SAlisbury, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven was not heating properly
took out the old element after cutting the circuit breaker, put in the new one, it was that easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Catasauqua, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven wouldn't heat
Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Newport, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
the old oven element burned in two.
After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new element from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Charlotte, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom element cracked/split - open circuit
Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.
Al S.
Al S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Vancouver, WA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Element broke
First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Wetumpka, AL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Oven would not heat up
Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 days. They still don't have the part. Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodolfo from Waterford, MI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Handle bracket was broken
Unscrewed the broken door handle from the range with torqx bit, and replaced, hardest part was getting the plastic handle on the black pull bar. you may want to use a mallet.
Was this instruction helpful to you?
Thank you for voting!