91195191990 Kenmore Range - Instructions

DO NOT ATTEMPT THIS REPAIR UNTIL THE RANGE IS UNPLUGGED AND THE CIRCUIT BREAKER IS OFF!!!!!!

Very easy repair, but, either there is a minor amount of current flowing through the element at all times, or the off switch wasn't working when I started. didn't turn the breaker off, after I removed the nuts, as I was pulling the element to reveal the terminals, the terminals arc'd on the oven wall. BIG SPARKS!

After I turned the breaker off and started again. No problems.

This was so easy I should be a repairman! Turned off power at the breaker, used socket to unscrew two hex head screws, pulled out element slowly from the back of oven wall - enough to expose the wires about 3". Used pliers to remove clips from terminals, put new element in, pushed on new terminal clips, fed wires and terminals back through the two holes, replaced the hex head screws, turned breaker on and wallah! My wife was happy! That's a good thing.

I was able to remove the heating element but in the process one of the wires fell behind the back wall of the oven so I needed a little help getting it out. It was my first time working with electricity. If this didn't happen the repair would have been quit easy. The instructions were great.

Removed oven door from oven. Removed the inner oven door portion from the outer part to gain access to inner screws attaching end caps to front of stove door. Removed those screws and the old end caps & broken off pieces. Pressed oven door handle bar into new end caps. Reattached oven door handle assembly to front of oven door. Reinstalled inner oven door which included long screws that also went into the new end caps. Reinstalled oven door on oven. Job was easy. Price was certainly right for the end caps at $10.01/each.

remove two screws slide out. slide new one in. put two screws back. done.

i was really pleased getting the order from partselect. i had torn my oven appart and knew i needed just this one part i came home and ordered it from parts select and actually got the part the next day.... very nice.... so pleased

The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years

First I unscrewed the end of the oven door and realized I could replaced the parts easily that hold the handle on the door. Then I held the sharp, broken plastic ends with a towel and used my drill with a thingy that fits on a small hex nut and unscrewed the broken handle parts and removed them. All I had to do after that is screw on the new handle holders with the handle bar fit snuggly between them, presto, new handle bar installed. Great service from partselect. com. Would use them again.!

I read the previous repair stories and figured it couldn't be that tough. Mine actually had a slight deviation and I'm sure based on model...
To remove the oven door handle, I had to remove 3 screws (phillips) on the top of the hinged door. This allowed the face plate to easily pull away from the inside of the door. The existing handles were held in place by a single hex head screw each.
Voila, in 2 minutes the entire handle was off.
This is where things had a slight deviation.
The door end caps I bought had 2 alignment prongs that extended beyond the actual surface. My door did not have holes for them to go into. No big deal, I took some wire snippers and clipped the little plastic prongs off so it was flush like my old ones. That took about 3 minutes because I had to go back into the garage to get the tool :-)
My metal door handle bar did not want to go all the way in very easily into the end caps. I went back into the garage and got some WD40 and sprayed into all pieces and wiggled things back and forth for a few minutes, placing it against the oven a couple of times to ensure I had the bar was seated enough where the holes lined up with the oven.
I would recommend putting the end caps on the bar PRIOR to attaching one side to the oven. I originally did not do this and when it was difficult to get the bar on, I had to take it off so I could perform the procedure I just mentioned.
Honestly, the entire "job" took 10 minutes.

Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm.

Although the parts did fit, some modification was needed to remove the excess tabs as it appears these parts were for multiple applications. However the end result was a good fit and reapirs were successful.

Followed the video directions on your website - GREAT INFORMATION. Everything went very smoothly It took me longer to find my work light (after turning off the electric to the oven) out in the garage than it did to complete the repair!! SUPER PLEASED - WOULD NOT HESITATE TO RECOMMEND THIS COMPANY TO ANY DIY ADVENTURER!!

Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.

Had to take back off of the door to get to screw that held the broken piece of handle before installing the new part. Then had to put the back on the door and slip the door into place.

Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.