91193471891 Kenmore Range - Instructions

Remove two screws holding element. Pull element forward exposing connections. Pull connections apart. Replace with new element. replace screws. Done

First I removed the two screws holding the element to the back of the oven. When I pulled the element out I disconnected the two wires and removed the element. I found the serial / part number on the existing part and order from PartSelect. The element arrived two days sooner than expected!! Replacing the element was a bit more difficult in that I had to pull the stove away from the wall and remove the rear cover in order to pull the wires and element through the insulation in the back of the oven. Four screws held the rear cover, but once those were removed the element easily went into place and the repair was finished. Cleaning behind and under the stove took a few extra minutes but the entire repair only took about 30 minutes, plus the wait time for the part. Two tips, pliers were used to disconnect and reconnect the slip-on connectors. The connectors were pretty tight and reaching to the rear of the oven was difficult to get leverage to pull apart and reconnect. Also, the oven light caused considerable glare on my glasses so I taped the door button controlling the oven light and used a flashlight to see inside. Otherwise, a simple repair. PartSelect had the best price on the element and service and delivery were excellent!

Very simple. Two small hex shaped screws hold the unit to the back of the stove. Remove those with a small socket wrench. Rachet type makes the job easier. Gently pull the element from the back of the stove. Remove the two push-on wires from the element. They simple pull off. The elements have supporting feet toward the front. Those must be down to rest the element on the bottom of the stove. Replace the push-on wires, push the element back into the holes in the rear of the stove and screw the small hex shaped screws back into the oven wall. The job is done.

I followed the directions in the video on the website. The repair was so easy!! I simply unscrewed the screws holding the element in place at the back of the oven, pulled the wires out. This did take a little bit of time, as I didn't want to pull the wire off of the element and lose it in the back of the oven, but I was able to eventually work it free from the insulation and make the connectors visible. I slid off the old element, slid the wires back on to the new one and pushed them back into the wall of the oven and replaced the screws. Works like a charm!! I will definitely use your website for other appliance repairs!!

Pulled oven from wall, Unplugged oven from outlet, Took 5/16 nut driver pulled back cover off oven to expose the quick connect wires, Pulled wires off old element, Opened oven door took the 2 screws off bracket on back of oven, Removed old element, Put new element in place, Put the 2 wires back on, Buttoned back up check to see if worked it did ((:

Unplugged the stove. Unscrewed the element. opened the rear cover to reach wires. Passed wires through the slot and connected the element. Screwed the element in place. Reinstalled the rear cover. Plugged the stove and pushed it back to place. Tested the oven, it worked.

Very easy repair. Part came wrong the first time (my fault for ordering the wrong one). Called and ordered the correct one after a closer match to the original part. Delivered much quicker than promised (one day) and installation very easy. Will use this site for all future repairs.

Well...you'll notice in other tools I put Tweezers. Now you really don't need tweezers if you do it right in the first place. Here's what I did: 1) unscrewed the nuts that hold the element in on the back of the unit. 2) Then pulled the terminals out of the holes in the back of the oven. OOPS...there were sparks as the right terminal wire hit the metal frame of the back of the oven. Scared me. I jumped. the terminal wire burned/broke off and fell back into the hole. Yep...Too late I remembered that the VERY first step of this repair is 1)CUT OFF THE POWER TO THE OVEN. I repeat...THE FIRST STEP IS TO CUT OFF THE POWER TO THE OVEN. I couldn't reach the wire with the needle nose pliers so I had to go get the tweezers. Couldn't see the wire but I just put the tweezers in about two times and it finally caught on the wire and I was able to pull it out. Luckily the terminal end was still connected to the wire so I didn't have to replace it. From there it was 3)remove the old terminal posts from the wires (used the needle nose here to wiggle the ends off - been on a long time), 4)insert the new ones, 5) push the terminal posts back in the holes, 6) screw the nuts back on, 7) bake the cornbread. A very quick job -- plus the element from PartSelect was almost half the price of any other I found (due to this I was able to upgrade the shipping a little to get it sooner and still saved money over any other price I found. Just remember to CUT OFF THE JUICE BEFORE YOU START this repair and it will be done in 5 mins or less.

I actually don't remember if instructions came with purchase. I have purchased appliance parts from here before and they did on previous times. I watched a couple of YouTube videos because I'm a visual guy (as I think most guys are) and the only difference between my reality and the video was I had nuts holding the element in place and the video had screws holding it in place. Extremely easy!! TURN OFF POWER TO STOVE.....PLEASE. Confirm power is OFF (clock not working...range wont turn on....something like that) Take oven door off hinges (mine just slid off without any problem). Remove defective element from oven. In the back there are two screws or bolts, take them out. SLOWLY pull old element out. Be careful and look for the insulation that will try to come out of the hole and watch for the wires that are attached to the element. The wires will come out far enough for you to work with them (about 6" or so). Be very careful NOT to jerk wires through holes too much or damage them. Remove wires from element. I used two pliers, one on element and one on wire crimp...I also sprayed wd40 on the connection prior and let it set for a short time before to loosen it up. Once separated, discard old element. Get new element and reverse the process. I reconnected wires, making sure to put them back in the exact same side they came off of. Ease the element power prongs back through the holes (VERY CAREFULLY, DON'T RUSH AND TEAR IT UP). The new element will fit exactly where the old one came off and just put the screws or bolts back in place and be VERY CAREFUL NOT TO STRIP THE SCREWS OR BOLTS. Turn power back on at breaker and turn on oven to check and see that it works. It should work great. This is the second part I've purchased from these guys and both jobs went flawlessly. I HIGHLY RECOMMEND these guys...plus it's almost the only place I could find to get the parts, but still they are great.

unscrewed it unhooked the wires and replaced with new part

Super simple to repair, removed back cover on oven (after turning off breaker), removed old terminals from over, had to bend new element slightly close to terminals, installed new and replaced oven cover. Less than 15 minutes.

I watched the video on the website then installed the part. In fact, I watched the video twice because I could not believe it was that easy. You can not do any better than PartSelect. Shipping is fast and the instructions are great. If I ever need a part for any appliance I will go to PartSelect.com first. Keep up the great work and thank-you so much!

We were able to purchase the part and replace it for under $25. We took off the oven door and installed the new element in under 10 minutes.

Removed nuts holding element to rear of oven using nut driver, pulled wires out 3 inches and disconnected using needle nose pliers, installed new element. Job took 10 minutes - very easy job and works fine.

Watched youtube....