3627272590 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nicholas from Elkridge, MD
- Parts Used:
- WB2X9154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
oven igniter would not heat so gas valve would not open
removed the old part with socket set and replaced the part with a fresh one. turned on oven, igniter heated up and oven lit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Bayside, NY
- Parts Used:
- WB2X9154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven broiler worked but oven would not ignite
Remove oven door,just open slighty and pull door up no tools.Take oven draw out.Remove oven floor held by two nuts in rear.You will now see the igniter,remove two screws holding it and the one screw holding the long tube at the front.The best tool I used was 1/4 drive socket set with a 6" ext.I did'nt need a new bracket that came with the part and I cut the old igniter wires and wired in the new one because it had a special connectors.If your are a handy person,its EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- OLABODE from MATTESON, IL
- Parts Used:
- WB2X9154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The oven igniter was not functioning.
Removed the oven door and the bottom plate. Remove existing igniter by cutting the wire and unscrewing two small bolts. The installation of the new part is the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Brethren, MI
- Parts Used:
- WB2X9154
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not light - no glow igniter
Removed bottom of oven Removed bottom drawer. Removed two screws holding burner, disconnected both wires.Removed two screws holding igniter,installed new igniter reversing procedure.
Could not get at the screws holding the igniter to the buner, without removing the burner.
Could not get at the screws holding the igniter to the buner, without removing the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heather from Wauconda, WA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were plugged
We bought our replacement burners from Part Select.com at half the price of another major appliance store. They came fast & fit perfect. All around, we are very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doan from Flushing, NY
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner did not light
just lift the cover and put it on.less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Houston, TX
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
old burners were rusty and broken
I just lifted the old part and dropped the new one in. Everything fits perfectly. The new flame is a beautiful blue color.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emir from New York, NY
- Parts Used:
- WB2X9154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Igniter would not start
1.Took out the metal pan.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Berkeley Springs, WV
- Parts Used:
- WB2X9154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not come on.
I changed out the old ignitor with the new one. New ignitor fit perfect on old mounting bracket. Attached the two wires and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from south st. paul, MN
- Parts Used:
- WB2X9154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven wont turn on but broiler does
Replaced the oven igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hyojin from Monmouth Junction, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The pipe that carry the gas to the ignition part was damaged, therefore the burner was not lightening up.
Just have to remove the old kit and replace it with the new one. No tool required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Reseda, CA
- Parts Used:
- WB20X107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
defective spark module
used nut driver to remove old module and 10 minutes the cooktop was back in operation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Warwick, RI
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
The key here was that I found the correcd part for an older kenmore oven and it was easily installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Franklin, NC
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one of the stove top burners had burned all the way through
matched part needed on web site; took off burner; ordered part; received it on the third day and easily replaced it. Wonderful, easy, and very short delivery time! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clare from north brunswick, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old burner assembly could no longer be cleaned
pop up range top. pull off old burner. put on new one.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
Was this instruction helpful to you?
Thank you for voting!