91146564012 Kenmore Range - Instructions

Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven. I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.

First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and reconnecting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.

.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.

pull out, push in

My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.

I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.

Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices!
Thank you,

1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace of tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.

unscrewed it unhooked the wires and replaced with new part

Removed oven door & shelves. Removed the 2 mounting screws & compared parts to verify I ordered the right one, then plugged it right in! Managed to drop & lose one of the screws while re-installing them. Got a stainless sheet metal screw from the hardware store that fits, but will probably order an exact replacement because the size & thread are slightly different. All in all, other than losing the screw, it was a quick, easy task.

Two screws hold the element to the oven wall. two wires attached to the back of the element. very simple removal and replacement.

shut power off to range, took 2 screws out, took 2 snap on clips off old element. put snap on clips on new element, put 2 screws back in, and turned breaker on.

I removed the 2 nuts and pulled the element out until I reached the disconnect and unhooked the elements from the wire. Replaced the new one in reverse order. It was great finding the part here after Sears said they no longer made the part.

Remove the oven racks, remove the two retaining screws, unplugged the wires. Install wires on new bake element, insert element into opening, install & tighten retaining screws, replace oven rack's & there you have it.

First - really check that the part you order will fit. Our oven is 30 years old and the first part we ordered was not correct, but it came the very next day after we ordered it which is amazing. We were more careful about measuring for the second one and it came almost as quickly. It only took a few seconds to unscrew the old element and then reattach the wires to the new one and screw it back into the oven. Very simple. I highly recommend PartSelect.