20233 Kenmore Range - Instructions

With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.

Easy

I removed the old element and replaced it with a new part. It was very simple.

The power was turned off. The elemnt wiring was removed. The new one was installed in reverse order. Power back on and the oven tested just fine.

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

unplugged oven. removed oven racks.Disconnected old unit. Installed new unit. Very very simple

The bake element in my 17 year old GE free standing electric range became defective. This element has 2 terminals -- black (240V) and white (neutral). While removing the element from the range, a 2nd black wire was pulled out of the back of the oven. This wire had a bare terminal connection and apparently had been loose behind the oven shell for all these 17 years. Inspection of this wire showed it carried 115V. I wrapped this wire with electrical tape and reinserted it into the insulation behind the oven shell.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

I removed the burner, then the chrome dish. The nuts for the wires were rusted to the terminals, so I had to break the module apart and grind the nuts off.After that the new module went fine.

The new element arrived in just 2 days with normal postage. I followed the simple instructions and was cooking 15 minutes later. It couldn't have been easier. Thanks.

Removed the bracket holding the element, slid out the element, disconnected it from the leads, replaced it with your part and reassembed. Oven now works like new.

1)Unscrewed the mounting nuts, 2) pulled the heating element out a couple of inches, 3) unscrewed the screws holding the wires in place, 4) removed and tossed the old heating element, 5) placed the new heating element in place, 6) re-screwed the wires to to the element, 7) pushed the heating element back into the wall of the oven, 8) reset the mounting nuts, 9) cleaned up the work area, 10) cranked up the oven and made a pizza. I'm not particularly skilled when it comes to things of this nature, but it was ridiculously easy...

I noticed two screws held the heating element in place. I removed the screws. Pulled the heating element out a few inches. Removed the two additional screws which held the two wires on.

To install the new element, I used the two new screws that came with the element to attach the wires to the element. Insert the element into position and attached the element to the rear wall with the two screws which were first removed.