36262788000 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Landisville, PA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
My son turned on the burner to make something and then there was a pop and stove would not work.
First I removed the burners and pulled the stove out to get the back cover off. Removed the back cover after main power was shut off. Removed old burner terminal blocks and replaced with new ones. Replaced back cover and pushed stove back into place. Turned on main power to stove checked burners and they worked. DO NOT REPLACE OR DO ANY ELECTRICAL WORK ON ANY MAJOR APPLIANCE WITH OUT FIRST TURNING OFF THE MAIN POWER SOURCE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rickey from Childress, TX
- Parts Used:
- WB30X46987
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower oven element burned into
Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from UNION SPRINGS, NY
- Parts Used:
- WB31T10011
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip bowls had deteriorated after years of use
Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wilson, WY
- Parts Used:
- WB2X8228
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Replace rangetop burner connectors
Since we got the stove,this is the second time we've repaired these connectors. The first time the connectors came with pre-stripped wires, wire nuts and heat shrink tubing. This set came with pre-attached spade terminals, so I had to crimp the mate to the wires in the stove then put heat shrink tubing on the splices. I also had to bend the part of the connector that mounts onto the stovetop. These had a horizontal tab for the mounting screw rather than the vertical design that our ranges uses. If the connectors designed for the earlier model were available, it would simplify installation since shrink wrap and wire wraps came in that kit and the mounting bracket would fit correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caren from Choctaw, OK
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowls
I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Readsboro, VT
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
stove top burner not heating
The longest part of the job was finding my misplaced nut driver!!Note:A small socket set will do.Unplug stove from outlet,remove rear cover panel,lift stove top up to access terminal. remove the one screw that holds the terminal and slide off the two wire clips that hold the wires up out of the way.next clip off the old terminal leaving the old wires so you can tape the new wires on just to pull them through the hole.Once you have the new wires pulled up to the heat control unplug old and replace with the new,tighten the screw on the new terminal and don't forget to slide on the wire clips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from st marys, GA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
part replacement
pull out, push in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bayani P. from DALY CITY, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burnt Terminal Block
Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SUZANNE from DAVID CITY, NE
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Wouldnt Bake Food Very Well It Took To Long To Bake
First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlean from Lyon, MS
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
lower element burned out
after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- selvon from MA, MA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner inop
Received complete burner receptacle. Decided to take off stove back to plug in directly to burner control.
Turn on stove on low. No heat. Bad coil element. Checked for power at coil element. Switched another burner. It heated immediaetly. Have to order or find a burner element
Turn on stove on low. No heat. Bad coil element. Checked for power at coil element. Switched another burner. It heated immediaetly. Have to order or find a burner element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIGUEL from NEW HAVEN, CT
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
the terminal was broken and rusting so the burner was not heating well
Removed the back cover with a socket tool, unplugged the old terminal and plugged in the new one. there is a screw holding the terminal block. so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Surry, VA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bakeing element burned out
Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Blue Hill, NE
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element went bad
turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vance from williston, ND
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The burner had been replaced and it shorted out ;thus discovered thath the wiring block kit was faulty. The parts ordered were a snap to replace the original .
Shut the power off and unscrewed facial hardware ,unplugged terminal and unscrewed hold down bracket and redid everything that I mentioned above. For a rookie it was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!