RER305CD0 Kelvinator Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- charles from killbuck, NY
- Parts Used:
- 5303051519, 08002868
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Original Bake Element stopped heating
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires with a pair of pliers do to the tight fit. Removed the old element and set the new one in place. Connected the two wires to the new element and squeezed the connectors tight. Push the element and wires back into the original position and used the new screws to secure the unit to the stove back. Took all of 5-6 minutes. Tested the oven with an oven thermometer at 250, 300, 350, 400 and 500 degrees and and all read within 5 degrees of the settings. Very easy, very simple, very quick.
Thank you for the quick responce and fast delivery of the parts.
Chuck Wells
Thank you for the quick responce and fast delivery of the parts.
Chuck Wells
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Ottumwa, IA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Original heating element broke due to dripped food.
Unplugged the appliance then removed the two screws holding the element in place. Pulled it out about 2-3 inches then pulled the wires off. The replacement element has 90 degree connectors as opposed to the original 180 degree connectors but that didn't affect installation and hasn't affected operation. Slide the wires on the new element, slide the element back in the oven, screw it back in and you're good to go. Trust me, easiest repair to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from Boise, ID
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element broke in half due to liquid dripping onto it.
Removed back of stove, removed screws holding old element. attached new element in same place, returned back to stove. My wife pushed element from inside stove into holes, which was a help. Voila! It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from roslyn, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
haeting element cracked
juist loosened nut and pulled element out about three inches, detached leads, reattached new leads and installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sheffield, MA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Found bake element cracked
Read the reviews and followed the same procedure. Very east..took about 10-15 minutes.
Product shipped same day/next day it was delivered and it was installed less than 30 hours after it was ordered.
Exceptional service.
Product shipped same day/next day it was delivered and it was installed less than 30 hours after it was ordered.
Exceptional service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Withams, VA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat
My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Temple, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element would not heat.
Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ocean View, AL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven burner was burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from belton, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven would not heat
took two screws out disconnected wires and connected new element ,screw back togather in about ten mins and started cooking dinner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Burkburnett, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Lower heating element not working
Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William G from Valdosta, GA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven bottom burner not heating
Locating part on web site, ordering, receiving next day & installing was very very easy. Information provided on PART SELECT web site and that provided with part made this a very easy and cost effective repair. With service provided by PART SELECT there is no reason to pay for an expensive service call in addition to what a repair company would charge for the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from orange, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven element was out
took me longer to find my 1/4 inch nut runner and drill than to change out the element.........simpliest replacement i've ever encountered and i'm 64 years old. less than 2 minutes......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from North Manchester, IN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element (lower element) in oven quick working
Even though my exact model was not matched by Parts Select the bake element shown in a picture for a different model was correct. The length the bake element protruded through the wall of the oven was the same as the old one. The element arrived within two days, packaged so it would not be damaged en transit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Freeland, MD
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
very little heat in the oven
The problem was that there was heat in the oven but only a little. This threw me off at first but my wife tells me that the broiler element is used as the oven heats up. So bottom line is, the main element was burned out and once I replaced it, everything worked fine.
Was this instruction helpful to you?
Thank you for voting!