Models > REP307CW5 > Instructions

REP307CW5 Kelvinator Range - Instructions

Jump to:

All Instructions for the REP307CW5
61 - 75 of 185
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Brandon from Lexington, NC
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Baking element went out
Removed back cover, unhooked wires, unscrewed and removed bad baking element. Reverse order to install. Less than 15 min. repair job.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Great Falls, MT
Parts Used:
5303051519
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Heating element cracked.
First unplugged the stove, then removed the screws holding the element in place. Next I pulled the element out until the wires were visible and unplugged them. After removing the old element, I plugged the new one in and positioned it with the screws. Plug the stove back in and done.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Navarre, FL
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Baker Element burned out
Really easy process. First I unplugged the oven for safety then I proceeded to remove the 2 screws that were holding the old element in place. Next I removed the old element then installed the new one. After installing the two screws I connect the oven back to its power source and BANG!............. It works like a charm

I give it a A+ installation
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pam from OCKLAWAHA, FL
Parts Used:
5303935086
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Can't regulate burners
Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Darragh, PA
Parts Used:
316067902
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Needed an additional rack
Open the door and slide in the new rack.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Denise from Landover, MD
Parts Used:
316538904
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light bilb went out
replaced it
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bennie from Kite, GA
Parts Used:
5303935086
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Burner will not cool down. I have to switch all the way off.
First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
steven from EPPING, NH
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
The bottom Heating element burned out.
I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Dayton, OH
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Baking element cracked
Removed the baking element with a nutdriver. Slid it to the front of oven and removed the contacts on the back side. Installed the new element and installed the contacts at back of element. Slid it in the holes on back inside of oven and used a nutdriver to install the screws. It was very simple to do.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BJ Machine Co., Inc. from Mauston, WI
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Burned out bake element
Try to buy new unit from local dealer, was told unit was too old. Went on line to Part Select and found part needed and ordered part. When part came, I removed two screws from in oven and four screws from back of range, discorrected two wire leads from bake unit, removed old unit and installed new unit, connected wires, reinstalled back cover, and installed bake unit to oven with two remaining screws. Job done, oven is now working. The part costs with shipping was around $33.00, new oven $600.00. Thanks Part Select.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jerry L. from Kendallville, IN
Parts Used:
5303051519
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven wouldn't heat on Bake.
First shut power to oven off, removed the oven door and oven racks. Removed the 2 screws from the back of the oven holding the element in place. Slowley pulled the element out and removed the wires, pulled off with my fingers. Replaced the old with the new in the reverse order. Saving the Wife a pile of money.

Thank You,
Jerry R
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
nancy from vancouver, WA
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Noticed the element was bent and bulging
Shut off the power at breaker to range,removed the screws and pulled out the element a few inches to disconnect the wires .Connected wires to new element., screwed it back into oven wall.It's a snap!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Angel from cleveland, OH
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
the bake element was broke in half
first i remove the two screws that hold the element then i pulled the element out few inches out i disconect the two wires and i put the new element back in place 10 or 15 minutes top.really easy
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Galen from Ulysses, KS
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Baking Element had fallen into 3 pieces
Repair was simple. Unplugged stove, removed a plate from back of stove. Disconnected wiring. Removed screws from inside oven, removed old element, installed new element. Replaced screws, hooked up wiring, replaced back plate, plugged it in, used it that night.
Thanks for sending the right part the first time and getting it shipped so quickly.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
yrna from Farmers Branch, TX
Parts Used:
5303051519
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
heat element would not heat.
Turned off power to oven at breaker box.
Removed one screw that holds the element in place. The other screw would not unscrew, I went to hardware store for drill bit and special hand tool (which cost less than $15) to remove stuck screw. I didn't have the right size screw, so I went back to hardware store for two new screws. Pulled the element out and disconnected the two wires(they are plug-in). Lost one wire into the back of oven because I did not hod it for the new element to plug onto. I removed the back of oven by unscrewing several screws and located the wayward wire. I threaded it back into the hole (easy) and someone grabbed it and held onto it while I screwed the back of the oven back on. Then I placed the wire connectors onto the new element being sure to squeeze hard with pliers so there would not be any slipping off of the wires. The power was restored and the element worked great. A less than 30 minute job took over 2 hours because of inot thaving he right tools.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the REP307CW5
61 - 75 of 185