REP309CT1 Kelvinator Range - Instructions

First I disconnnected the breaker for the oven and then removed the broken element by unscrewing the screws that held it in with a nut driver. I then pulled the element out exposing the connected wires. I removed the wires from the element by pulling them off with my fingers. Using a set of hemistat pliers I secured the wires so they wouldn't slip into the holes at the back of the oven. I connected the new element by slipping the connectors onto the element and finished by putting the ends of the element back into the holes and securing it into place with the screws using the nut driver.

removed element , cut wires, conected wires,replaced element

First turned off the breaker to the oven, I opened the oven door, took out the baking racks, removed the two screws that hold the element in place. Pulled the element out about 3 inches, disconnected the wires, Installed the new element in the reverse order.

Turn off the electricity
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity back on
Cook dinner :)

I could see a visible burnout on the element.
Got it really fast.
Removed two screws, pulled it out, disconnected two wires. installed a new one in, and was done!

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
Really really easy . I am a single woman with no repair experance and had no problems.

Twisted replacement bulb into place easily. Let there be light!

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

installed terminal block kits and burners worked great

simple ratchet extension and socket to remove screws and replace. be sure to crimp the connectors with pliers before ataching the element.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Pulled out the range, unplugged it and removed the upper back panel. The switches were held in place with two screws. Removed the old switches, detached the wires and plugged them into the new switches. Mounted the new switches, replaced the back panel, plugged the range back in and pushed it back into position. Appliance repair company wanted $370. I did it in 45 min. for less than $100.

Removed back access panel of oven (several screws). Unplugged element wires (two slip connectors). Removed two element mounting screws from the inside of oven, and removed old element. Reversed proceedure to install new part.