RER355DW0 Kelvinator Range - Instructions

I just followed the instructions that I found online.

I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.

***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.

Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

I just watched the video, unplugged the stove, attached the burner and started baking again. DSC

It was fast and easy! I unplugged the oven, unscrewed the element, then pulled it out. Unhooked the wires. Then hooked the wires to the new element and screwed it back on, plugged it in and then started cooking.

shut the breaker off , remove the racks' use nut driver to remove the 2 screws, carefully slid the element ends out of the holes, disconnected the wire ends (push on connectors) discarded the old element and replaced with the new in reversed order. very simple

1. Remove two screws securing element to rear wall of oven. 2. Carefully pull element forward until you have access to the wires attached to the element. 3. Carefully pull the push-on connectors from the element. 4. Push wires onto new element. 5. Carefully push element back into oven wall and secure with screws.