REP305A1D Kelvinator Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.

first i removed the two screws that hold the element in place. then pulled out about 3 inches
and disconnected the wires.installed in reverse
order.

Easy to open package and plug in unit! Too simple and quite happy with end results!

Unplugged stove, use nutdriver, removed screws, pulled out old element, put in new one. Done. As prescribed. Excellent help as well as got part the next business day.

I used this site self diagnostic page and ordered the oven heating element as that was the item suggested for repairs. It was the correct part to fix my oven problem. I had my electrician visiting to install two light fixtures so I had him install the new heating element in the oven. Even with him going to the garage to turn the circuit breaker off for the range the installation took less than 5 minutes.
This site is the greatest!

Thank for having the part necessary to put the old range back in shape. The repair job was simply to unplug the old one and plug in the new one! Great simply job!

took me longer to find my 1/4 inch nut runner and drill than to change out the element.........simpliest replacement i've ever encountered and i'm 64 years old. less than 2 minutes......

Even though my exact model was not matched by Parts Select the bake element shown in a picture for a different model was correct. The length the bake element protruded through the wall of the oven was the same as the old one. The element arrived within two days, packaged so it would not be damaged en transit.

The problem was that there was heat in the oven but only a little. This threw me off at first but my wife tells me that the broiler element is used as the oven heats up. So bottom line is, the main element was burned out and once I replaced it, everything worked fine.

Locating part on web site, ordering, receiving next day & installing was very very easy. Information provided on PART SELECT web site and that provided with part made this a very easy and cost effective repair. With service provided by PART SELECT there is no reason to pay for an expensive service call in addition to what a repair company would charge for the part.

Working on 33 year old Kenmore stove (Harvest Gold color bought in 1977). Have replaced the element every 12 to 14 years, last in 1997. 3-5 FedEx delivery took only 1 day. I verified Selector dial and Temperature dial both set to off. I took out the 2 oven shelves and took off the oven door for easier access to back of oven. Open oven door slightly to 1st catch, slightly lift and pull door away from the oven to clear the 2 side hinges from the openings. I used 1/4 inch socket with ratchet to remove 1 screw on each side holding element to back wall of oven. Gently pulled element out and up slightly so connectors come through openings in back wall. 1 connector came out from wall 4 inches, the other just barely. I used needle nose pliers to pull connector off element with 4 inches of wire. The connector did not come off easily, it took some wiggling of the connector (not too hard because it is brittle). I pulled connector off element barely out from the wall and held the connector in the pliers (did not let go). Put old element on kitchen floor and put new element on oven floor. Attached connector wire to end of element so it didn't slip through back wall. Attached connector wire to other end of element. Lifted element slightly to push through back wall openings. Used 1/4 inch socket to re-attached both screws. I put oven door back on (reverse of taking off). I set Selector to Bake and Temperature to 300. I watched element heat up (nice solid color along entire length) and reach 300 temperature and cycle off. I opened oven door to force the thermostat to kick in the cycle again. I closed oven door to watch the element again. When the heating cycle finished, I turned the Selector & Temperature to off. When oven cooled off, I put the shelves in again.

took out the screws at the back of the oven, removed the old element and put the new one in, replaced the screws. The new part was mostly the same size as the old one, some of the angles were different and the ends slightly different, but it fit and works great.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.

First, trip the circuit breaker for your stove. Second I removed the two screws ( 1/4" nut driver makes this go quickly ) that hold the element in place. I then pulled the element out about 3 inches ( double check the electricity is off with your tester )and disconnected the two wires from each side of the element. Press connectors on new element and slide back in.

Just took the back of the stove off and removed old one and put new one in. Very simple.