REP309CD3 Kelvinator Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Tallapoosa, GA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Baking element burnt out and broke in my hand.
First I cut the breaker to the oven. Then pulled racks out of oven. Then used my nut driver to take the two screws of the back mounts. I then pulled the broken part out and installed the new one. I was not sure at all about doing this until I read some of your other testemonies, but after that, I became an oven repairman. The very next day after instalation, my wife cooked me a ham and a pan of cornbread! Thanks for the fast service, y'all got me back to eating my wifes homemade dinners within three days of ordering my part. There is no way to thank you for that, but here is a very large THANK YOU! I will definitely be back(hopefully not soon!) when I need other appliance parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- staci from pleasant hill, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
our oven wouldn't heat when we needed to bake something.
took the screws out and then put the new element in and that was all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conan from Moline, IL
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Two burners did not heat
Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Bonita Springs, FL
- Parts Used:
- 318036310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs for the three timers on the appliance console deteriorateddue to age.
The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monty from WILKESBORO, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Shorted out baking element.
Took out bottom drawer and unplugged power cord, slid unit out to reach back panel,removed front door( 2 Phillips screws) making it easier to reach back of oven, removed screws inside of oven holding element in place, took plate off rear and removed the spade connectors with needle nose pliers. Slid new element into oven and replaced screws inside of oven. Connected the two spade wires on the back and replaced rear panel. Slid unit back in place and plugged the 220v power cord back in. Straightforward and very simple! It took 3 times longer to clean the oven while it was disconnected than it did to replace the element.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from WEATOGUE, CT
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original Element physically broke
There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony J from HAMMONTON, NJ
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the burner stop working
Just followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Falmouth, MA
- Parts Used:
- 5304409888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny L from CHELAN, WA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heavy jam boiler caused elements to sag
Removed the old & simply inserted the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Roanoke, VA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lacking oven racks on used appliance
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Spencer, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" stove top element would not warm up.
It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Lake Luzerne, NY
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element burned out
I turned off the circuit breaker to the range. Next I removed the two screws that fastened the element to the rear of the oven. Then I pulled the element out far enough to be able to reach the spade clips and disconnected the element. I connected the replacement element to the clips and fastened it to the rear of the oven with the two screws. I turned the circuit braker on and the element functioned properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROMEO from HANOVER PARK, IL
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bake element not working
Removed the old element by sliding the wires
attached to it. Unscrew 2 screws, slide the
new one to the wirings and put the 2 screws back.
It works. Praise the Lord.
attached to it. Unscrew 2 screws, slide the
new one to the wirings and put the 2 screws back.
It works. Praise the Lord.
Was this instruction helpful to you?
Thank you for voting!