Models
>
D-100
D-100 Jenn-Air Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This down-draft fan switch kit has a gray rocker switch and two metallic push nuts. At 125 volts,this switch will allow for 6 amps, and at 250 volts, this switch will allow for 250 volts. This switch ...
No Longer Available
$105.39
This bake element is eighteen inches long. Its terminal depth is less than an inch long, and it comes with two screws.
In Stock
This selector switch knob is a chrome knob with black lettering denoting the different functions of the oven: broil, preheat, bake, off, etc. There is also a black plastic trim around the perimeter of the knob.
No Longer Available
This part establishes and maintains the internal temperature of the oven cavity.
No Longer Available
This oven door handle assembly is twenty-four inches long. The handle itself is black, but it has a metallic piece on each end. Also, this handle assembly comes with two mounting pads. Each mounting p...
No Longer Available
This grill element is just under eighteen inches long. It has three terminals and is used with some electric grills.
No Longer Available
The hinge allows the door to open and close. This can be used for either the left or right side of the appliance. Sold individually.
No Longer Available
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for D-100
Viewing 2 of 2Little to no heat when baking
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leon from Sandwich, IL
- Parts Used:
- 12001130
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Blower quit working
I removed the two screws that held the electrical
switch control. Then I raised the control upward an tilted it sideways an jumped the two terminals with a screwdriver. then i knew the switch was bad. So then i removed the two pail nuts that held the switch to the switch control an removed the old switch. Then installed the new switc ... Read more h in the reverse proscess. This was fairly easy
switch control. Then I raised the control upward an tilted it sideways an jumped the two terminals with a screwdriver. then i knew the switch was bad. So then i removed the two pail nuts that held the switch to the switch control an removed the old switch. Then installed the new switc ... Read more h in the reverse proscess. This was fairly easy
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shan'te from Saint Joseph, MI
- Parts Used:
- WP715269
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bake element not working
Our oven is at least 30 years old and the parts are not even available through the manufacture anymore. A new stove would cost well over $1000.00. Jen airr is the only down draft stove available. So the repair was much more affordable that the alturnative. So thank you to part select for providing this service. The repair was simple. Th
... Read more
is is coming from a 36 year old female who has been around electrical work, but never done any myself. My husband was out of town and I felt I could do the job. I first made sure I had another adult present. I turned off the power to the oven. I then removed the visible screws to the element plate (2 on top and 1 in lower middle). I then pulled the element out enough to get behind the plate and feel the screws that were connecting the wires to the element/ground. Again 3 total. The oven space is very small and difficult to work in. I had to do a lot by feel. Once the old element was free I just exchanged it for the new one and reversed the process, making sure all the wires were tight. I then turned the power back on. Turned the oven on, it smoked lightly for a moment and turned red hot. Over all it was extreemly simple.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Flower Mound, TX
- Parts Used:
- 12001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fan switch was broken
-turned off power to stove
-lift off grill cover to downdraft
-remove 2 screws
-cut retaining clips with wire cutters
-remove old switch
-replace with new switch and push on new retaining clips
-remove and replace wires
-replace covers
-turn power back on
-lift off grill cover to downdraft
-remove 2 screws
-cut retaining clips with wire cutters
-remove old switch
-replace with new switch and push on new retaining clips
-remove and replace wires
-replace covers
-turn power back on
Was this instruction helpful to you?
Thank you for voting!