20236 Jenn-Air Range - Instructions

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!

My husband and I couldn't believe we were able to do this!!!So easy! We were dancing around the kitchen!!!!! We credit the advice of other do-it-yourselfers. Very accurate and true. It took less than 10 minutes after the screws were WD40'd. In addition, we recommend: use a flashlight to see in the oven since it's dark with the power cut off , and use this time to clean behind the stove!!!!!

I removed the back of the stove for easy access to the wiring (three hex head screws) and removed the two wire leads. Then I began to remove the mounting screws from the inside of the oven, the first three screws came out fine the last one was so tight that I had to resort to vise grip pliers. Jenn-Air should have used hex head screws instead of phillips head inside the oven. Finally after about 15 minutes the last screw came out. I installed the new element, reinstalled the screws and wires. Then I replaced the back and tested. Total about 45 minutes.

It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.

switch went well
removed 4 screws and lifed front panal up and out

Shut off electrical breaker to stove. Unscrew & remove heating element with standard screwdriver. Since screw threads were stripped I used a longer screw I wrapped thread with teflon tape. Connect new heating element & crimp connectors to ensure contact is made, push wires back & tighten screws. Turn power breaker back on & we have a new oven!

Replaced the control.

First we removed the door from the stove. Removed all the screws and removed the damaged seal. We replaced the seal and re-assembled the door.

Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.

Removed front wooden kick panel(2 cross recessed screws).
Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete

Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.

switch power supply off at breaker panel

unscrew control box assembly from stove

slide control out of stove

unscrew burner control out of assembly

transfer wiring from old control to new in same relative location

reassemble in reverse order

restore power

test burner in all positions

Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.