20236 Jenn-Air Range - Instructions

The frame and window were supplied as a completed assembly. About 4 other panels had to be removed prior to installing the new window assembly. This was easy to do with a screwdriver removing about 16 screws and then replacing all panels back in place after replacing the new window assembly. No instructions were supplied with the part, but anyone with a little mechanical abillity could do it. You may need a helper to hold panels in place while they were being screwed back in place. Total job took about one hour

First step is turn the power to the range off. Then I removed the grate covering the down draft vent in the center of the cook top. Inside the vent opening are two screws that secure a panel that holds the four knobs that control temperature settings. Remove these screws. Slide the panel tward the back of the range while lifting it up. This will allow removal of the panel. Remove the knob from the burner control you are replacing. Under the knob are two screws. Remove the screws and let the controller drop out of the cover panel. Take the new switch and carefully remove the wires from the old controller and place them on the new controller in the same position. When the wires have been connected, put the controller back in the control panes and secure it with the two screws. Replace the panel back into the cook top. Tilt the control panel so the front is low and the back is elevted. Engage the lugs protuding out on each side of the control panel opening. Lower the panel back into the opening and secure it with the two remaining screws. Replace the control knob and you are done. You just saved yourself a $125.00 service call. Total cost for the controller $35.00.

Removed the door then the end caps and inner panel then the hinge system and replaced with the one piece new set of hinges and back together done in 30 to 45 minutes The new parts were a perfect replacement.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Purchased 2 piece broiler pan from this site

We panicked cause even simple repairs on these products cost and cost.....but we remained calm and ordered the exact part necessary from you. It arrived in just 3 days and once we had the part in hand it was easy to understand how to replace it. We disassembled the door with screwdrive and swapped the broken part with the new one. The one gotcha was that we were not aware of the shipping pin holding the spring and we struggled for a few trying to get the door closed all the way. Once we discovered the pin and removed it, it was fixed and we were PLEASED!

Thank you,
Louise and Rickl

Removed fan housing from under stove and replaced motor. Biggest job was cleaning the fan housing as a lot of kitchen grease had accmulated of the life of the stove.

take door off. remove screws holding door together, take door apart. remove worn seal. install new seal. reposition insulation and door window at the appropriate location. begin re-assembling door in reverse order making sure that apprpriate pressure is applied to keep the seal in place. re-attach door to hinges. project worked out well. new seal looks great. would have been a costly repair if I called a professional. I'm handy, but things like this are often hard the first time. you have to take your time and be cognizant of putting it back together the way you took it apart.

part came quickly and fit perfect... everything works great...pretty simple repair... nice to have the right part and have it arrive so quickly

First, I made sure the circuit breaker was off to the oven. Next, I removed the two screws that hold the element in place , pulled the element out a few inches and eased the wires apart at the metal connectors. I eased in the new wires, put the two screws back in, and voila. In under five minutes, the oven was fixed.

I replaced the hinges as described in other posts and the problem was solved. When the oven was 2 years old it had the same problem but the hinges should not have fatigued at that point. The engineering problem someone mentioned is that the pin of the light switch is too short. I touched it with lipstick, closed the oven door, and opened the door to see exactly where the door touched the pin. I drilled a small hole in the door and screwed in a self tapping metal screw...problem solved for 8 years until the hinges fatigued. After replacing the hinges I tried removing the screw but the light stayed on so I put the screw back.

Had to disassemble the top of the stove and the control panel on the front. I took digital pictures as I disassembled so I could refer to them when putting the stove back together, especially when disconnecting wiring. It took about 3 hours, but most of that time was spent thoroughly cleaning 16 years of baked on grease from places that are normally unaccessible. The new latch works great - the wife is happy!

I changed out the infinite switch without any problems. The indicator light was another problem. It wasn't the light that was bad, it was the indicator light lens that snaps into the panel. The light then attaches to the lense. The lense broke and the indicator light pulled away with the tension on the wires. Now I have to order replacement lens and will have a spare indicator light.

We made the mistake of taking the door apart before we received the replacement parts. After waiting several days, which was fine, the parts arrived. Then we had to figure out how it went back together. My wife and I did it and enjoyed working on it. However....after getting it partly reassembled, we (I) found four extra screws. We took it apart again and then put it back together. Turning the door over we found that the glass assembly had slipped. This meant that we had to take it apart again. This went on two more times LOL. Then the gasket gave us a couple of small fits as well. All in all it was a neat experience. I do suggest, unless you are experienced in appliance repair, to NOT disassemble the door until the parts arrive.

The comments from others on the website were a great help.

Thank you.

The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.