JDS8850BDS Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Douglas from La Habra, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken electrode
First I tried twitching my nose....after I stopped sneezing I got a screw driver and put the new electrode in and gosh in gahiggy, it worked!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from roseville, MN
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would overheat
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Boardman, OH
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode cracked, spark misdirected, poor lighting
After determining it would not be possible to replace the electrode only (rusted/corroded connection), ordered burner head with electrode. Part came in approx. 24 hours. Actual repair involved removing two screws (star-shaped head),disconnecting electrical clip, removing part, connecting electrical clip to new head, reinstalling two screws. Works great now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from nanticoke, PA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner porsclend was cracked and would not light
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KARL from OCEAN, NJ
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner ignator split--
unscrewed old ignator---replaced w new--done deal!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Grand Junction, CO
- Parts Used:
- WP74011666
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic burner knob split and would not turn burner off & on
pulled the old ones off and replaced them with a much stronger better designed knob. EASY PEASY!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Tampa, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F1 Fault Code - Replace the Temperature Sensor
The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Iuka, IL
- Parts Used:
- WPW10154101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner Head was leaking gas from side
I lifted the burner tray from stove turned it upside down then removed six small screws from side of cover pan then I removed the cover then I removed the screws from the back of the old burners and igniter.Then I turned the old burner counter clockwise and it lifted out easly. the igniter is removed with no problem. The new burner is put in place and turned clockwise to lock in place.Then replace then the gas tubes and igniter and igniter wire then put tray cover on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilfred from Hoover, AL
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven tempature varies.
We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Globe, AZ
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper oven shut down after reaching temperature
The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Acworth, GA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My oven was not holding temperature.
I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sanbornton, NH
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner igniter didn't light burner
I removed the burner by unscrewing 2 torx head screws, disconnected wire from electrode, removed screw holding electrode, inserted new electrode,connected wire, installed burner and fired it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carson City, NV
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged Ignitor
Simply unscrewed the old one and installed the new one and we have ignition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from winter haven, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
temperature varied in oven.couldn't set
removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Ipswich, MA
- Parts Used:
- 74004857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Outer glass from oven door shattered
Removed oven door (slides out). Removed side and bottom screws from frame and slid new glass into place. screwed in the 8(or so) screws.
Was this instruction helpful to you?
Thank you for voting!