JES8750BAB16 Jenn-Air Range - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.

I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!

Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

The feedback from other customers was excellent. It does come apart in layers, and it helped me to number each layer with a sticky note as I dismantled it. I also kept the screws for each layer right next to the layer, so that I knew how many screws each layer used. The only thing I can add is that the tabs to remove the innermost glass from the frame are on one of the shorter sides of the rectangular frame. The tabs are part of the frame, and when you bend them outward the side of the frame detaches and you can replace the glass easily. In addition to the #1 Philips screwdriver, all I needed was a pair of pliers to bend the tabs.

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Removed the two screws, on both sides of the oven wall corner. Gently lift the front end of the glass top and pull towards me and disconnect the two electrical sockets. Carried the glass top assembly on the kitchen table and turned upside down. Removed the six screws. Removed the assembly from the glass top. Turn the top burners assembly over and disengaged the two clips of the burned out burner from the assembly plate. Transferred the two clips to the new burner on the exact locations like the old ones were. I have placed the new burner on the location and snapped the clips on the slots. Removed the connectors one piece at a time and connected to the new burner. Reversed the previous disassembly and all was done Works like a charm. Thank you all for assisting me in providing the necessary parts and video instructions. It was a lot cheaper than to buy a new range.

Removed burned out burner, replaced new burner tested works fine

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou