JGA8100ADW11 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cecil from REDFIELD, SD
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
j just look at it and figure how itcomes apart and reverse when installation complete easy
took out burner and remove ignite r and reinstall a new one simple as that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from WOODBURN, OR
- Parts Used:
- 74004053
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Back burner would not light
I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tao from Frisco, TX
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the shell if the igniter was broken
find the part (image is really helpful), buy, and replace. Like I said, it's really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from brooklyn, NY
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner very hard to get out
Used strap wrench to turn out. Rust build up under the burner. Used flat screwdriver to loosen under burner and strap wrench to turn out. Then replaceing the igniter was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robin from saint marys, GA
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
2 burners rusted apart, 1 gas valve frozen up.
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Vashon, WA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wore out burner and igniter
New burner and igniter.....actually it was very easy to to fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Osage Beach, MO
- Parts Used:
- WP74005890
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas burner would not light-had to use lighter
As described for the part. Easy repair. Easy to diagnose thanks to feedback from another customer of yours. Part was received super fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Inga from Petaluma, CA
- Parts Used:
- WP74005890
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Only two burners lit
Removed old igniter set replaced with new one. Hardest part was using the screw driver to removing the backing. Saved us having to buy a new stove since we just bough the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Block Island, RI
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken insulator for top burner igniter
I have a Magic Chef gas stove, The top burner came off with ease, just a quarter turn then pull up to expose igniter. Only two wires to remove and two phillips head screws to remove to release igniter. I was done in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Godfrey from Las Cruces, NM
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement of top burner igniter
Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Soledad, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter not working
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from massillon, OH
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The igniter on my stove wouldn't ignite.
Watched a video on replacing igniter. Removed old igniter and replaced it with new igniter.
Was this instruction helpful to you?
Thank you for voting!