JER8885RCS1 Jenn-Air Range - Instructions

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I turned the braker off the electric range and removed the bottom plate that housed the bake element (two screws had to be removed). There were three screws that held the bake element in place. I pulled the bake element from the two electrical prongs that connected to the oven. I replaced the element and put everything back in place.

More importantly than all of the above. I received the part from Partselect in two days. When I originally put the eleemnt in its place it did not work. I called partselect and was issued another element in two days. The people I spoke to on the phone were proffessional and sympathetic to my problem. I will definetly recommend this company to other people. Thank you very much....

The Maytag stove has a hidden element and therefore I had to remove the bottom cover to expose the element. I had to remove the three screws that held the element in place. The element was badly bent out of shape and must have been that way since new. It was difficult to remove the element and I had to pull the stove out to access the electrical connection in the back to disconnect it. The replacement part was a perfect fit and the installation of the new part went with out hitch and the oven works perfectly.

remove stove , unplug power , took back panel off, disconnected wiring to the heating element, from the inside of the stove removed bottom plate /two screws/, removed heating element /two screws/. installed new element .put other parts in order they were removed

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

Ordered the part late Wednesday night and paid for standard shipping. The part arrived Saturday morning, we removed the old part and screwed in the new one. It took minutes! We were shocked at how inexpensive the part was, how user friendly this site is and how quick the order arrived. We will def use this site again!

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.

Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

i simply followed your instructions,so easy my wife could have done it with her pink screwdriver!!! thanks for your help.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

Removed door from oven. Removed 6 screws to dismantle door. Removed 3 more screws to remove hinge from door...reverse order to assemble.
Very easy