JER8895BAS11 Jenn-Air Range - Instructions

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

Real easy, I removed the two screws holding the element in place, then pulled the element out a few inches to reveal the wire connectors. pulled the connectors from the old element and then replaced with the new one and screwed it back into place and presto! All done and cooking again. The replacement part came in 2 days fast and reliable. Thanks PartSelect.com

Ordered the part from your company. It arrived promptly. Gave to to my two sons 22 & 29. They fixed it.

Very easy........................................

I had to remove the screws that held the range top in place. Next just removed the existing element (leaving the wiring in place). Replace wires one at a time and then placed all the screws on the new element.

Turned OFF the circuit breaker. Unscrewed the old and screwed in the new. Very easy. There were helpful hints from other people on the web site, ie. turn off the circuit breaker first.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

slide stove all the way out. Remove front, then top, unhooking two wiring harnesses. Took pictures of existing wires to make sure to get back in same place. Pull element wire connections off. Replaced element and reconnected. Fairly easy.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Only hitch I experienced was identifying the correct replacement. The original diagram presented the accurate shape of the element my range required. However a different shaped element was displayed when I noted my unit is a series 12 serial number. I ordered it (with reservations) and as it turned out the replacement was identical to mine. Next time I will have a lil more confidence in the instructions given.

When the element failed, it continued to glow nearly white-hot and slowly burned along a spiral path on the element. I figured this MUST be due to a voltage leak - the control was OFF on the range.

I shut off the breaker, removed the two screws where the element goes through the back of the oven, pulled the element forward and pulled the wires off of the element. (Found it handy to twist the wire connectors outward to prevent the wires from slipping through the back of the oven.)

A new element won't "fit" exactly but you can easily push it into position to get the screw holes to line up. Total time was less than 15 minutes.

Put a new one in.

removed screws and disconnected the wires removed element and did the replacement less than 15 minutes, and cost less than locally by 25.00 and received part the next day. EXCELLENT

Unplugged the power cord first. Opened oven door and removed the two screws that held the stove top glass down. Lifted the glass top and removed the four wires connected to the element. I taped the wires to the lid in the pattern they were attached to the element. remove the element from the brackets. The new element was an exact match. reversed the sequence. Put a pot of water on and boiled a hot dog! Perfect! Great part and speedy delivery!!

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!