JGS8850CDB01 Jenn-Air Range - Instructions

Put a new one in.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

replaced heat sensor

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

1. Remove the oven door by opening a few inches and lifting straight up. Remove racks to access it. 2. The old igniter is just held in by two nuts that have a screw head in the middle of them so they could be removed by a nut driver or by a screwdriver. Unfortunately, both of our screws threads were terribly stripped and after first trying to use pliers to help remove them, we ended up using a dremel tool to cut them off. 3. unplug the old igniter and take it out. 4. Plug in the new igniter. 5. attach the two screws. (our time on the repair was mostly spent trying to find two screws around our house that would replace the two that were stripped--otherwise this would have been 15 minutes). 6. return the door and racks by the sliding the door downwards onto the hinges

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

Watch the video. Spot on instructions. Easy peasy.

The porcelain cracked on the burner igniter, it wouldn’t spark and light the flame. I got tired of using the fireplace lighter to light this main burner.

If you have to replace your igniter, it should be very very easy. Remove the two torx screws Holding the cast iron burner to the stainless steel top. Pull it up and the wire connected to the igniter should pull through the small hole in the stainless steel top. Turn the cast-iron base over, pull the wire off, and there is a little screw Fastening the igniter to the bottom of the cast-iron Base. Remove the old igniter and screw the new igniter in place, reattach the wire, and screw the base down to the stainless steel top. That’s it, or how it should be. After years of spaghetti water, gravy, etc. boiling over, I was only able to remove one of the torx screws after using some WD-40 and a torch to heat it up. The other screw sheared off at the head. And a little screw holding the igniter in place, the Phillips head was stripped! I had to leave the roof or the igniter in place, break off all the porcelain, and then break the rest of the metal off leading the screw in place. So I had to use my Dremel grinder to remove some of the metal on the new igniter, then use some tinfoil underneath it to stabilize it in place and then tighten the cast-iron base down using only one screw. Even with one screw and using the tinfoil, it is stable and everything works now. This $27 part was a heck of a lot cheaper than paying $5000 for a new range top!

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

This should be a 5 min job. Lift off the burner cover, remove two screws to lift of the burner base and then remove a Phillips head screw that hold the burner igniter in place.

Unfortunately, the screw holding the burner igniter was rusted and it could not be loosened. WD-40 did not touch it. I used a stronger penetrant, "Blaster". Still it would not budge. Then I used a small Phillips head screwdriver and a hammer which I used as an impact driver. I twisted the screwdriver slightly to loosen and hit it was a hammer. Then I twisted the screwdriver slightly to tighten and again hit it with a hammer. After the penetrant and a couple of more tries, the rusted screw finally moved!!!

With no rust, this should be an easy 5 minute replacement. The burner now works great!!!

Installation is simple and very straight forward. Problem, was i stripped the torx screw to release electrode because the screw was frozen. I then tore electrode out leaving space to use penetrating oil (inaffective ) then using a chisel to pop the screw out. It came out intact and did not damage the threads in the burner. So what could have been a 20 minutes job, turned into over an hour. But still worth doing myself.

I ordered a new igniter and when it arrived, i removed the door from the oven. It just lift's off. I had to removed two screws from the bottom plate to gain access to the igniter. Remove the two screws from the igniter and unplug it from the back of the lower back of the stove. Place the new igniter where the old one was and plug it in. Put new screws in and tighten them down. Put the bottom plate back in its place with screws tightened. Put oven door back on and turn on the oven. That's all there is to it. Your done.