Models > JDR8880RDW1 > Instructions

JDR8880RDW1 Jenn-Air Range - Instructions

Jump to:

All Instructions for the JDR8880RDW1

Customer:: DAVID from Cape Coral, FL
Parts Used:: 12001656
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

When We Turned On The Oven The Temp. Reading Went Up To 425 And Beeped By No Heat

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

Was this instruction helpful to you?

Customer:: Gary from San Jose, CA
Parts Used:: 12001656
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

F-4 Code, oven wouldn't heat

Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.

Was this instruction helpful to you?

Customer:: Dennis from Tampa, FL
Parts Used:: 12001656
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

F1 Fault Code - Replace the Temperature Sensor

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

Was this instruction helpful to you?

Customer:: John from Dacula, GA
Parts Used:: 12001656
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Fan runs continually ,door locked,error code f2,f3,f7

Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

Was this instruction helpful to you?

Customer:: Frank from Roseburg, OR
Parts Used:: WP74009147
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Broken burner knobs

Popped broken ones off and slipped new ones on. Fairly straight forward and easy.

Was this instruction helpful to you?

Customer:: Stacey from Tampa, FL
Parts Used:: 12001656
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven would not turn on

Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.

Was this instruction helpful to you?

Customer:: Timothy from Longmeadow, MA
Parts Used:: 12001656, 8009
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Oven have F2 and F3 codes following cleaning cycle making oven inoperable

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

Was this instruction helpful to you?

Customer:: MARK from roseville, MN
Parts Used:: 12001656
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven would overheat

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

Was this instruction helpful to you?

Customer:: Lloyd from Eau Claire, WI
Parts Used:: 12001656
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

change oven sensor

Followed provided video

Was this instruction helpful to you?

Customer:: Cindy from Polson, MT
Parts Used:: 12001656
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Had code F1 and F3 on my oven. Oven wouldn't heat.

Watched the video and it was as easy as described. Not many things go as easily as this.

Was this instruction helpful to you?

Customer:: Grant from Alexandria, VA
Parts Used:: 8009
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Light bulb failure

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Was this instruction helpful to you?

Customer:: Don from Crestwood, MO
Parts Used:: W11665456
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers

Broken leveling leg.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Was this instruction helpful to you?

All Instructions for the JDR8880RDW1