JDR8895BAB13 Jenn-Air Range - Instructions

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

Removed 2 phillips head screws, disconnected the 2 wires. Installed new element, connected wires then installed screws. Took less than 3 minutes. What i liked was how fast I received the new element. Ordered online on Friday around 12:30 and received Saturday morning by 9:00 AM. Excellent transaction!

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

I removed the two small screws, gently pulled the element outward, slid the wire connectors off the ends of the element legs and reversed the process to install the new one. THE ELEMENT STILL DOES NOT HEAT. There must be a bad switch or thermostat at the ON switch area. That will be checked out by a Repair man as soon as I can get a schedule from him.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Make sure you unplug your stove before you start! You should probably shut off the power at the breaker box too.

Since the upper oven is so small, I found that I couldn't reach the connectors well enough to work with them. So I pulled out the whole oven, took the screws off the back cover and from the back I was able to easily reach where the wires connected to the element. Then it was a piece of cake.

Just use a small knife to unbend the little metal things that hold on to the metal ends of the element. Slide them on to the new element, and crimp them tight with pliers.

Oh, you also have to take off the bracket on the ceiling of the inside of the oven to get the old element out, and the new one in.

The oven has been working great!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Repair would have only taken minutes, but upper support plate screws were rusted and almost fused to the plate. Once the plate screws were out (had to pry plate out) installation was done in 3-5 minutes.

As for the replacement part, worked perfect on the first try. Very happy with price, speed of delivery and preformance.

I had the old oven rack in the oven when I cleaned it. The rack came out brown and would not slide easily. The new rack was exactly the right one and now all is back to perfect!

Turned off breaker to oven, removed racks, unscrewed the plate holding the element in place, and pulled out the wires a few inches. All easy and fine to this point. Never having done anything like this before, I wasn't sure HOW the element was attached to the wires, so tugged on them a bit, but nothing budged. Got a flashlight (it got dark in there with the upper part of my body in there)looked again, but still couldn't tell. Referred to this site and saw reports of "plug and play", went back and examined the ends more closely on old and new element, realized that they slide straight on and straight off in a "sleeve". Got some pliars and pulled the ends apart. Slid the new end on to one wire, but couldn't get the other one on until I realized I had crushed it a bit with the pliars. Reopened the "sleeve" with a vegetable knife and slid the other end of the element into the "sleeve" at the end of the wire. Then pushed the wires back in and screwed plate on. It took about 23 minutes, and that included time to look up this site and do some reading, jump up to find a flashlight, and jump up and find a pair of pliars. My hubby was out of town for 3 weeks and suggested I wait til he got home--glad I didn't wait.

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

I just bought my first condo and sure enough something broke in my oven. I thought "Oh great - I'll need to buy a new one..." After some research and a friend's advice - I was assured that I only needed to replace the broiler element. After researching the issue I googled replacement parts which led me to this web-site. I was amazed how easy and inexpensive it was for me to replace the part. The directions were easy, simple, and spot-on! The instructions that were provided were easy to follow. I also utilized YouTube instructions as well for additional visual guidance. The shipping was super fast and the element was packaged very well. Thank you so much!

Shipped on timely manner,I will order again from Part Select, installing was a 15 minute job, that what I did, 1 unplugged stove, 2) removed 4 screws, (2 on top bracket and 2 on back) , 3) slide unit out couple inches enough to disconnected the wires from each end of unit and removed old part, installed new unit by reconnecting end wires, pushing unit slowly toward back of oven until wires find it's right position, set it back in place with the 2 screws on top bracket and 2 screws on back, done!!

Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range.