JDS8850CDS01 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Hendersonville, NC
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor cracked and would not light
Simply removed the old ignitor and install the exact replacement part. Work great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from La Habra, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken electrode
First I tried twitching my nose....after I stopped sneezing I got a screw driver and put the new electrode in and gosh in gahiggy, it worked!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janine from Hatfield, PA
- Parts Used:
- WP7801P173-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing Oven Rack
I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carson City, NV
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged Ignitor
Simply unscrewed the old one and installed the new one and we have ignition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Boardman, OH
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode cracked, spark misdirected, poor lighting
After determining it would not be possible to replace the electrode only (rusted/corroded connection), ordered burner head with electrode. Part came in approx. 24 hours. Actual repair involved removing two screws (star-shaped head),disconnecting electrical clip, removing part, connecting electrical clip to new head, reinstalling two screws. Works great now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KARL from OCEAN, NJ
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner ignator split--
unscrewed old ignator---replaced w new--done deal!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from nanticoke, PA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner porsclend was cracked and would not light
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from roseville, MN
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would overheat
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Ipswich, MA
- Parts Used:
- 74004857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Outer glass from oven door shattered
Removed oven door (slides out). Removed side and bottom screws from frame and slid new glass into place. screwed in the 8(or so) screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Tampa, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F1 Fault Code - Replace the Temperature Sensor
The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Globe, AZ
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper oven shut down after reaching temperature
The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilfred from Hoover, AL
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven tempature varies.
We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Bellefonte, PA
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1 Pane of Inner Safety Glass
It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Deer Park, IL
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Burner electrode was damaged during cleaning
A crack in the porcelain caused the spark to not go in the proper direction, therefore the burner would not ignite. To have the job done by a professional would have cost $200.00 plus parts. Remove two phillips screws lift the burner out then remove the one phillips screw that held the electrode. Then with the new electrode in place reverse the previous steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Monee, IL
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner did not light
Ordered online Tuesday, delivery by FedEx on Wednesday. Removed the old "popped" in the new and it worked right away. It was that simple. Thanks so much.
Was this instruction helpful to you?
Thank you for voting!